Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.
MAR 2011
24-Hour Service Hotline 1-800-551-8633
* 8 1 9 6 5 5 7 *
E-mail: [email protected]
Please read all sections of this manual and retain for future reference.
NOTICE
This appliance is intended for professional use only and is to be operated by qualified
personnel only. A Frymaster Factory Authorized Service agency (FAS) or other qualified
professional should perform installation, maintenance, and repairs. Installation, maintenance,
or repairs by unqualified personnel may void the manufacturer’s warranty. See Chapter 1 of
this manual for definitions of qualified personnel.
NOTICE
This equipment must be installed in accordance with the appropriate national and local codes of
the country and/or region in which the appliance is installed. See NATIONAL CODE
REQUIREMENTS in Chapter 3 of this manual for specifics.
NOTICE
Drawings and photos used in this manual are intended to illustrate operational, cleaning and
technical procedures and may not conform to onsite management operational procedures.
NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS
U.S.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) This device must accept
any interference received, including interference that may cause undesired operation. While
this device is a verified Class A device, it has been shown to meet Class B limits.
CANADA
This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set
out by the ICES-003 standard of the Canadian Department of Communications.
Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A
et B prescrites dans la norme NMB-003 edictee par le Ministre des Communications du Canada.
NOTICE
IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS MANITOWOC
FOOD SERVICE EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART
PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS AUTHORIZED SERVICE
CENTERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL
CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER, FRYMASTER DEAN AND ITS
AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY
THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO
THE INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN
UNAUTHORIZED SERVICE CENTER.
NOTICE
The Commonwealth of Massachusetts requires any and all gas products to be installed by a
licensed plumber or pipe fitter.
DANGER
Improper installation, adjustment, maintenance or service, and unauthorized alterations or
modifications can cause property damage, injury, or death. Read the installation, operating and
service instructions thoroughly before installing or servicing this equipment. Only qualified
service personnel may convert this appliance to use a gas other than that for which it was
originally configured. See Chapter 1 of this manual for definition of qualified service personnel.
DANGER
Adequate means must be provided to limit the movement of this appliance without depending
upon the gas line connection. All fryers equipped with casters must be stabilized by installing
restraining chains. If a flexible gas line is used, an additional restraining cable must be
connected at all times when the fryer is in use.
DANGER
The front ledge of the fryer is not a step. Do not stand on the fryer. Serious injury can result
from slips or contact with the hot oil.
DANGER
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
DANGER
Instructions to be followed in the event the operator smells gas or otherwise detects a gas leak
must be posted in a prominent location. This information can be obtained from the local gas
company or gas supplier.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container
at the end of frying operations each day. Some food particles can spontaneously combust if left
soaking in certain shortening material. Additional information can be obtained in the filtration
manual included with the system.
WARNING
No structural material on the fryer should be altered or removed to accommodate placement of
the fryer under a hood. Questions? Call the Frymaster Dean Service Hotline at 1-800-551-8633.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal
the joint between the frypot. Banging fry baskets on the strip to dislodge shortening will distort
the strip, adversely affecting its fit. It is designed for a tight fit and should only be removed for
cleaning.
FINDING YOUR WAY AROUND THE FRYMASTER BK1814 GAS
SERIES
BK1814 Series Gas Fryers
Installation & Operation Manual
TABLE OF CONTENTS
Page #
1-1
1.
INTRODUCTION
1.1
1.2
1.3
1.4
1.5
1.6
After Purchase
1-1
Ordering Parts
1-1
Service Information
Computer Information
Safety Information
Service Personnel
1-1
1-1
1-2
1-3
2.
IMPORTANT INFORMATION
Receiving and Unpacking Equipment
General
2-1
2-1
2-2
2-3
2-3
2-3
2-5
2-5
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Principles of Operation
Rating Plate
Pre-Installation
Air Supply and Ventilation
Equipment Installed at High Altitudes
3.
INSTALLATION
3-1
3-1
3-2
3-7
3-9
3.1
3.3
3.6
3.7
Installing the Fryer
Gas Connections
Adjustments/Adaptation to Different Gases
Electrical Connections
4.
FRYER OPERATIONS
Initial Start-up
4-1
4-1
4-3
4.1
4.2
Final Preparation
1814 Series Gas Fryers
Installation & Operation Manual
TABLE OF CONTENTS (CONT.)
Page #
5-1
5.
FILTRATION INSTRUCTIONS
5.1
5.2
5.3
5.4
5.5
Draining and Manual Filtering
General Filtration Information
Filtration Preparation
5-1
5-2
5-2
Daily Filtration Operation
Operating the Filter
5-6
5-8
6.
PREVENTATIVE MAINTENANCE
General
6-1
6-1
6.1
7.
TROUBLESHOOTING
General
7-1
7-1
7-1
7-2
7-4
7-7
7.1
7.2
7.3
7.4
7.5
Pilot Burner Malfunction
Main Burner Malfunctions
Wiring Diagram, Main
Wiring Diagram, Filter
BK1814 Series Gas Fryers
Chapter 1: Introduction
1.1 Applicability and Validity
The Frymaster 1814 Series gas model family (HD models) has been approved by the European
Union for sale and installation in the following EU countries: AT, BE, DE, DK, ES, FI, FR,
GB, IE, IT, LU, NL, NO, PT and SE.
This manual is applicable to and valid for all Frymaster 1814 gas units sold in English-
speaking countries, including those in the European Union. Where conflicts exist between
instructions and information in this manual and local or national codes of the country in which
the equipment is installed, installation and operation shall comply with those codes.
This appliance is only for professional use and shall be used by qualified personnel as defined
in Section 1.7.
1.2 After Purchase
In order to improve service, have the following chart filled in by the Frymaster Authorized Service
Technician who installed this equipment.
Authorized Service
Technician/FAS
Address
Telephone/Fax
Model Number
Serial Number
Gas Type
1.3 Ordering Parts
Customers may order parts directly from their local factory authorized service center. For this
address and phone number, contact your factory authorized service center or call the Frymaster
Service Hotline phone number, 1-800-551-8633.
To speed up your order, provide the model number, serial number, gas type, part needed, item part
number (if known), and quantity needed.
1-1
BK1814 Series Gas Fryers
Chapter 1: Introduction
1.4 Service Information
Call the Frymaster Service Hotline, 1-800-551-8633, for the location of your nearest factory
authorized service center. To assist you more efficiently, always provide the service technician with
the model number, gas type, serial number, and the nature of the problem.
1.5 Computer Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. While this device is a verified Class A device, it has been
shown to meet the Class B limits. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio
communications if not installed and used in accordance with the instruction manual. Operation of
the equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his/her own expense.
The user is cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
If necessary, the user should consult the dealer or an experienced radio and television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission
helpful: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available
from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
1.6 Safety Information
Before attempting to operate your unit, read the instructions in this manual thoroughly.
Throughout this manual, you will find notations enclosed in double-bordered boxes similar to the
ones below.
CAUTION
CAUTION boxes contain information about actions or conditions that may cause or result in a
malfunction of your system.
WARNING
WARNING boxes contain information about actions or conditions that may cause or result in
damage to your system, and which may cause your system to malfunction.
DANGER
DANGER boxes contain information about actions or conditions that may cause or result in injury
to personnel, and which may cause damage to your system and/or cause your system to malfunction.
1-2
BK1814 Series Gas Fryers
Chapter 1: Introduction
1.7 Service Personnel
A. Qualified and/or Authorized Operating Personnel
1. Qualified/authorized operating personnel are those who have carefully read the information
in this manual and have familiarized themselves with the equipment functions, or have had
previous experience with the operation of equipment covered in this manual.
2. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
3. Children should be supervised to ensure they do not play with the appliance.
B. Qualified Installation Personnel
1. Qualified installation personnel are individuals, firms, corporations, and/or companies, that,
either in person or through a representative, are engaged in and responsible for the
installation of gas-fired appliances. Qualified personnel must be experienced in such work,
be familiar with all gas precautions involved, and have complied with all requirements of
applicable national and local codes.
C. Qualified Service Personnel
1. Qualified service personnel are those who are familiar with Frymaster equipment and have
been authorized by Frymaster to perform service on Frymaster equipment. All authorized
service personnel are required to be equipped with a complete set of service parts manuals
and stock a minimum amount of parts for Frymaster equipment. A list of Frymaster Factory
Authorized Service agencies (FASs) was included with the fryer when shipped from the
factory. Failure to use qualified service personnel will void the Frymaster warranty on
your equipment.
1-3
Frymaster BK1814 Series Fryer
Chapter 2: Important Information
2.1 Receiving and Unpacking Equipment
A. Check that the container is upright. Use an outward prying motion - no hammering - to
remove the carton. Unpack the fryer carefully and remove all accessories from the carton.
Do not discard or misplace these, as they will be needed.
B. After unpacking, immediately check the equipment for visible signs of shipping damage. If
damage has occurred, contact the carrier and file the appropriate freight claims. Do not
contact the factory. Shipping damage responsibility is between the carrier and the dealer.
If your equipment arrives damaged:
1. File claim for damages immediately, regardless of extent of damage.
2. Visible loss or damage: Be sure this is noted on the freight bill or express receipt and is
signed by the person making the delivery.
3. Concealed loss or damage: If damage is unnoticed until equipment is unpacked, notify
freight company or carrier immediately, and file a concealed damage claim. This should
be done within 15 days of date of delivery. Be sure to retain container and all packing
materials for inspection.
NOTE: Frymaster Does Not Assume Responsibility for Damage or Loss Incurred in
Transit.
C. Frying systems with built-in filtration: Take off the filter support brace and remove the
filter pan from the cabinet.
D. 1814 four-battery systems: Casters are pre-installed on the frying system and the carton is
furnished with three unloading ramps. Remove the braces from the front casters by taking
out the securing bolts. Carefully roll the unit down the ramps from the front (cooking side).
E. Remove all plastic skin from sides, front, and doors of the fryer(s). Failure to do this prior to
initial fryer operation will make it very difficult to remove later.
2.2 General
Qualified, licensed, and/or authorized installation or service personnel only (as defined in
Section 1.6) should perform the following:
•
•
Installation and service on Frymaster equipment.
Conversion of this appliance from one gas type to another.
Failure to use qualified, licensed, and/or authorized installation or service personnel to install,
convert to another gas type or otherwise service this equipment will void the Frymaster
warranty and may result in damage to the equipment or injury to personnel.
2-1
Frymaster BK1814 Series Gas Fryer
Chapter 2: Important Information
2.2 General (cont.)
Where conflicts exist between instructions and information in this manual and local code or
national codes, or regulations, installation and operation shall comply with the codes or
regulations in force in the country in which the equipment is installed.
DANGER
Building codes prohibit a fryer with its open tank of hot oil/shortening from being
installed beside an open flame of any type, including those of broilers and ranges.
Upon arrival, inspect the fryer carefully for visible or concealed damage. (See Receiving and
Unpacking Equipment in Section 2.1.)
CAUTION
Frymaster appliances equipped with legs are for stationary installations. Appliances
fitted with legs must be lifted during movement to avoid damage to the appliance
and bodily injury. For moveable installations, optional equipment casters must be
used. Questions? Call 1-800-551-8633.
2.3 Product Description
Frymaster 1814 Series gas fryers are energy efficient, tube-style, gas-fired units. All units are
shipped completely assembled with accessories packed inside the frypot. All units are adjusted,
tested and inspected at the factory before shipment. Sizes, weights and input rates of all models are
listed in this manual.
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil frying system, particularly the aspects of
system operation, oil filtration, draining and cleaning procedures.
2.4 Principles of Operation
The incoming gas flows through orifices and is mixed with air in the burners to create the correct
ratio for proper combustion. The mixture is ignited at the front end of each heat tube by the pilot
light. Internal diffusers slow the flame as it goes through the burner tube. This slow, turbulent flame
increases heat transfer to the walls of the tubes to heat the oil more efficiently.
2.5 Rating Plate
This is attached to the inside front door panel. Information provided includes the model and serial
number of the fryer, BTU/hr input of the burners, outlet gas pressure in inches W.C. and whether the
unit has natural or propane gas orifices.
2-2
Frymaster BK1814 Series Gas Fryer
Chapter 2: Important Information
DANGER
Fryers MUST be connected ONLY to the gas type identified on the attached rating
plate.
2.6 Pre-installation
DANGER
No structural material on the fryer should be altered or removed to accommodate
placement of the fryer under a hood. Questions? Call the Frymaster Service Hotline
at 1-800-551-8633.
DANGER
Do not connect this appliance to the gas supply before reviewing all information in
this chapter.
NOTICE
The Commonwealth of Massachusetts requires any and all gas products to be installed by a
licensed plumber or pipe fitter.
A. General: Only licensed personnel should install any gas-fired equipment.
1. A manual gas shut-off valve must be installed in the gas supply line ahead of the fryers for
safety and ease of future service.
2. Parts protected by the manufacturer or its agent shall not be adjusted by the installer.
3. Frymaster 1814 Series gas fryers require 120VAC 60 cycle or 230VAC single-phase 50 Hz
(International) electrical service and are equipped with a 16-3 SJT grounded flexible power
cord for a direct connection to the power supply. Amperage draw for each unit depends on
the accessories supplied with the unit/system.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
B. Clearances: The fryer area must be kept free and clear of all combustibles. This unit is design-
certified for the following installations:
1. Commercial installation only (not for household use).
2. Non-combustible floor installation equipped with factory-supplied 6 in. (15 cm) adjustable
legs or 5 in. (13 cm) casters;
3. Combustible construction with a minimum clearance of 6 in. (15 cm) side and 6 in. (15 cm)
rear, and equipped with factory-supplied 6 in. (15 cm) adjustable legs or 5 in. (13 cm)
casters.
2-3
Frymaster BK1814 Series Gas Fryer
Chapter 2: Important Information
2.6 Pre-installation (cont.)
C. Installation Standards
1. U.S. installations must meet:
2. Canadian installations must meet:
American National Standard Institute
ANSI Z83.11
American Gas Association
8501 E. Pleasant Valley Road
Cleveland, OH 44131
CAN 1-B149 Installation Codes
Canadian Gas Association
55 Scarsdale Road
Don Mills, ONT, M3B 2R3
National Electrical Code
ANSI/NFPA #70
American National Standard Institute
1430 Broadway
Canadian Electric Code c22.1, part 1
Canadian Standards Association
178 Rexdale Blvd.
Rexdale, ONT, M9W 1R3
New York, NY 10018
NFPA Standards #96 and #211
National Fire Protection Association
470 Atlantic Avenue
Boston, MA 02110
3. CE/Export Standards: Fryer installation must conform with local codes, or, in the
absence of local codes, to the appropriate national or European Community (CE)
standards.
2.7 Air Supply and Ventilation
DANGER
This appliance must be installed with sufficient ventilation to prevent the occurrence
of unacceptable concentrations of substances harmful to the health of personnel in
the room in which it is installed.
Keep the area around the fryer clear to prevent obstruction of combustion and ventilation airflow as
well as for service and maintenance.
A. Do not connect this fryer to an exhaust duct.
B. Correct installation and adjustment will ensure adequate airflow to the fryer system.
C. A commercial, heavy-duty fryer must vent its combustion wastes to the outside of the building.
A deep-fat fryer must be installed under a powered exhaust hood, or an exhaust fan must be
provided in the wall above the unit, as exhaust gas temperatures are approximately 800-1000°F
(427-538°C). Check air movement during installation. Strong exhaust fans in the exhaust
hood or in the overall air conditioning system can produce slight air drafts in the room.
2-4
Frymaster BK1814 Series Gas Fryer
Chapter 2: Important Information
2.7 Air Supply and Ventilation (cont.)
D. Do not place the fryer’s flue outlet directly into the plenum of the hood, as it will affect the
gas combustion of the fryer.
E. Never use the interior of the fryer cabinet for storage or store items on shelving over or
behind the fryer. Exhaust temperatures can exceed 800°F (427°C) and may damage or melt
items stored in or near the fryer.
F. Adequate distance must be maintained from the flue outlet of the fryer(s) to the lower edge
of the filter bank. Per NFPA Standards No. 96, a minimum of 18 in. (45 cm) should be
maintained between the flue(s) and the lower edge of the exhaust hood filter.
G. Filters and drip troughs should be part of any industrial hood, but consult local codes before
constructing and installing any hood. The duct system, the exhaust hood and the filter bank
must be cleaned on a regular basis and kept free of grease.
2.8 Equipment Installed at High Altitudes
A. The fryer input rating (BTU/hr) is for elevations up to 2,000 ft (610 m). For elevations
above 2,000 ft (610m), the rating should be reduced four percent for each additional 1,000 ft
(305m) above sea level.
B. The correct orifices are installed at the factory if operating altitude is known at time of the
customer’s order.
2-5
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
3.1 Installing the Fryer
This appliance shall be installed in conformity with the current regulations and used only in a well-ventilated location.
A. Initial Installation: If the fryer is installed with legs, do not push the fryer to adjust its
position. Use a pallet or lift jack to lift the fryer slightly, and then place the fryer where it
is to be installed.
B. Relocating the fryer: Remove all weight from each leg before moving a fryer with legs
installed. Do not slide the fryer on the legs.
C. If a leg becomes damaged, contact your service agent for immediate repair/replacement.
3.2 Leveling the Fryer
A. All Installations: If the floor is uneven or has a definite slope, place the fryer on a level
platform.
B. Place a carpenter's spirit level across the top of the fryer and level the unit both front-to-
back and side-to-side. If it is not level, the unit may not function efficiently, the oil may
not drain properly for filtering and in a line-up it may not match adjacent units.
C. Adjust to the high corner and measure with the spirit level. If floor is uneven, level the
unit with the screw adjustments on each leg (ensure minimum clearances as discussed
in Chapter 2 are maintained during the leveling procedure).
D. Re-leveling: If the fryer is moved, re-level the fryer following the above instructions.
E. The install must be reviewed at the time of installation to ensure it meets the intent of
these instructions.
CAUTION
Fryers must be at room temperature, empty of oil, and if fitted with legs, lifted during
movement to avoid damage and possible bodily injury.
DANGER
Hot shortening can cause severe burns. Avoid contact. Under all circumstances, oil
must be removed from the fryer before attempting to move it to avoid oil spills, and
the falls and severe burns that could occur. This fryer may tip and cause personal
injury if not secured in a stationary position.
3-1
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
3.3 Gas Connections
DANGER
Before connecting new pipe to this appliance the pipe must be blown out thoroughly
to remove all foreign material. Foreign material in the burner and gas controls will
cause improper and dangerous operation.
U.S. NATIONAL CODE REQUIREMENTS
This equipment is to be installed in compliance with the Basic Plumbing Code of the Building
Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation
Manual of the U.S. Food and Drug Administration.
This equipment is manufactured to use the type of gas specified on the rating plate attached to the
door. Connect equipment stamped "NAT" only to natural gas and that stamped "PRO" only to LP
(Propane) gas.
Installation shall be made with a gas connector that complies with national and local codes.
Quick disconnect devices, if used, shall likewise comply with national and local codes.
DANGER
The fryer MUST be connected to the gas supply specified on the rating and serial number
plate located on the back of the fryer door.
DANGER
If gas odors are detected, the gas supply MUST be shut off at the main shut-off valve. The
local gas company or FASC should be contacted immediately to rectify the problem.
The gas supply (service) line must be the same size or greater than the fryer inlet line. This fryer is
equipped with a ¾" (22 mm) male inlet. The gas supply line must be sized to accommodate all the
gas-fired equipment that may be connected to that gas supply. Consult your contractor, gas
company, supplier, or other knowledgeable authorities.
Recommended Gas Supply Line Sizes
Gas Types
Number of Fryers
2 to 3
1
4 or more (*)
1¼" (35 mm)
1" (28 mm)
Natural Gas
Propane (LP) Gas
1" (28 mm)
¾" (22 mm)
½" (15 mm)
¾" (22 mm)
(*) When exceeding 18 feet for a configuration of more than four fryers, it is necessary to provide
a 1¼" (35 mm) rigid gas connection.
3-2
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
3.4 Gas Connections (cont.)
Gas Supply Type and Pressure
Gas Supply Type
Gas Supply Pressure
Natural Gas
Propane (LP) Gas
6-10" W.C. (Dynamic)
11-13" W.C. (Dynamic)
DANGER
When pressure-testing incoming gas supply lines, disconnect the fryer from the gas
line if the test pressure is ½" PSI [3.45 kPa (14 inches W.C.)] or greater to avoid
damage to the fryer’s gas piping and gas valve(s).
DANGER
All connections must be sealed with a joint compound suitable for the gas being
used and all connections must be tested with a solution of soapy water before
lighting any pilots.
Never use matches, candles, or any other ignition source to check for leaks. If gas
odors are detected, shut off the gas supply to the appliance at the main shut-off
valve and immediately contact the local gas company or an authorized service
agency for service.
DANGER
"Dry-firing" your unit will cause damage to the frypot and can cause a fire. Always
ensure that melted shortening, cooking oil or water is in the frypot before firing the
unit.
A. Rigid Connections: Check any installer-supplied intake pipe(s) visually and clean
threading chips, or any other foreign matter before installing into a service line. If the
intake pipes are not clear of all foreign matter, the orifices will clog when gas pressure is
applied. Seal pipe joints with a sealant resistive to LP gas. When using thread compound
on gas piping, use very small amounts and only on male threads. Use a pipe thread
compound that is not affected by the chemical action of LP gases. DO NOT apply thread
compound to the first two pipe threads—doing so will cause clogging of the burner
orifices and control valve.
B. Manual shut-off valve: This gas service supplier-installed valve must be installed in the
gas service line ahead of the fryers in the gas stream and in a position where it can be
reached quickly in the event of an emergency.
C. Regulating Gas Pressure: The fryer and shut-off valve must be disconnected from the gas
supply during any pressure testing of the system.
NOTE: External gas regulators are not normally required on this fryer. A safety control
valve protects the fryer against pressure fluctuations. If the incoming pressure is in
excess of ½" PSI (3.45 kPa/35 mbar), a step-down regulator is required.
3-3
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
3.4 Gas Connections (cont.)
DANGER
When pressure-testing incoming gas supply lines, disconnect the fryer from the gas
line if the test pressure is ½" PSI [3.45 kPa (14 inches W.C.)] or greater to avoid
damage to the fryer’s gas piping and gas valve(s).
D. Manifold Pressure: Your local service technician should check the manifold pressure with a
manometer.
1. Check the rating plate for specific manifold gas pressures. Natural gas units normally require
4" W.C. (10.0 mbar), and propane/LP units normally require 11" W.C. (27.5 mbar) gas
pressure.
2. Confirm that the arrow forged into the bottom of the regulator body, which indicates gas flow
direction, is pointed downstream towards the fryers. The air vent cap is also part of the regulator and
should not be removed. If a vent line from the gas pressure regulator is used, it should be installed in
accordance with local codes or in the absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1-(latest edition) in the U.S. and appropriate national or European harmonized standards
(EN) in the European Union.
WARNING
Use a leak detection fluid to find potentially dangerous gas leaks when making new
connections.
E. Regulators can be adjusted in the field, but it is recommended that qualified service personnel adjust a
regulator only if it is known to be out of adjustment or serious pressure fluctuations have been found and
can not be solved another way.
F. Only qualified service personnel should make adjustments to the regulators.
G. Orifices: The fryer can be configured to operate on any available gas. The correct safety control valve,
appropriate gas orifices, and pilot burner are installed at the factory. While the valve can be adjusted in
the field, only qualified service personnel should make adjustments with proper test equipment.
H. Flexible Couplings, Connectors and Casters: If the fryer is to be installed with flexible couplings and/or
quick-disconnect fittings, the installer must use a heavy-duty AGA design-certified commercial flexible
connector of at least ¾" NPT (with suitable strain relief), in compliance with the Standard for Connectors
for Movable Gas Appliances, ANSI Z21.69-(latest edition) and Addenda Z21.69a-(latest edition). Quick
disconnect devices must comply with the Standard for Quick-Disconnect Devices for Use with Gas Fuel,
ANSI Z21.41-(latest edition).
1. For an appliance equipped with casters, the installation in the U.S. shall be made with a connector
that complies with Standard for Connectors for Movable Gas Appliances, ANSI Z21.69-(latest
edition) and Addenda Z21.69a-(latest edition). In the European Union, use a flexible coupling
certified as NF D 36123 (or other national standard) or a quick disconnect device certified NF D
36124 (or other national standard). The coupling shall be periodically examined and replaced as
necessary.
3-4
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
3.4 Gas Connections (cont.)
WARNING
Do not attach accessories to this fryer unless fryer is secured from tipping. Personal
injury may result.
2. The fryer must be restrained by means independent of the flexible coupling or
connector in order to limit the movement of the fryer. Restraining brackets are
located on the back panel of the fryer for the attachment of restraints.
3. If disconnection of the restraint is necessary, this restraint must be reconnected after
the fryer has been returned to its originally installed position.
I. After hook-up, bleed the gas line of air to ensure that the pilot light will ignite quickly.
AUSTRALIAN REQUIREMENTS
To be installed in accordance with AS 5601 / AG 601, local authority, gas, electricity, and any other
relevant statutory regulations.
3.5 Gas Specifications
NON-CE (Altitudes of 2000 feet or less)
EQUIPMENT
PRESSURE
INPUT
(BTU)
GAS
ORIFICE
(MM)
ORIFICE
MODEL
QTY
TYPE
PART NO.
MBAR
INCH W.C.
NAT
LP
2.26(#43)
1.40(#54)
810-2049
810-2324
5
5
10
27.5
4
11
1814
115
NOTE: Outlet gas pressure must be adjusted strictly within the above requirements 5 to 10 minutes after the appliance is operating.
(Pilot Flame Adjustment: Turn the pilot adjustment screw clockwise/counter-clockwise until the desired flame-volume is achieved.)
CE ONLY (Altitudes of 2000 feet or less)
EQUIPMENT
PRESSURE
INPUT
(kW)
GAS
ORIFICE
(MM)
PILOT ORIFICE
(MM)
MODEL
QTY
TYPE
MBAR
INCH W.C.
G20
G25
G31
2,2
2,2
1,4
5
5
5
.46
.46
.33
10,0
15,0
23,9
4,0
6,0
9,5
1814
33,7
NOTE: Outlet gas pressure must be adjusted strictly within the above requirements 5 to 10 minutes after the appliance is operating.
(Pilot Flame Adjustment: Turn the pilot adjustment screw clockwise/counter-clockwise until the desired flame-volume is achieved.)
3-5
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
The 1814 Series gas fryer has received the CE mark for the countries and gas categories indicated in the table
below. NOTE: The nominal heat input (QN) is 21kW except for AT, DE, LU and category 3P/B, which is
23kW.
CE Approved Gas Categories by Country
COUNTRIES
CATEGORIES
GAS
G20
G30, G31
G20, G25
G30, G31
G20
G30, G31
G20, G25
G30, G31
G20, G25
G31
PRESSURE (MBAR)
20
50
20, 25
28-30, 37
20
AUSTRIA (AT)
II2H3B/P
I2E(R)B
I3+
BELGIUM (BE)
DENMARK (DK)
II2H3B/P
II2Esi3+
II2Esi3P
II2H3B/P
30
20, 25
28-30, 37
20, 25
50
FRANCE (FR)
G20
20
30
20
50
FINLAND (FI)
G30, G31
G20, G25
G30, G31
G31
II2ELL3B/P
I3P
GERMANY (DE)
50
G20
G30, G31
G20
G30, G31
G20
G30, G31
G20
G30, G31
G25
G31
20
28-30, 37
20
28-30, 37
20
28-30, 37
20
GREECE (GR)
ITALY (IT)
II2H3+
II2H3+
II2H3+
IRELAND (IE)
LUXEMBOURG (LU)
II2E3B/P
II2L3P
50
25
50
25
30
30
20
NETHERLANDS (NL)
G25
II2L3B/P
I3B/P
G30, G31
G30, G31
G20
G30, G31
G20
G30, G31
G20
G31
NORWAY (NO)
PORTUGAL (PT)
II2H3+
28-30, 37
20
28-30, 37
20
37, 50
20
30
II2H3+
II2H3P
SPAIN (ES)
G20
G30, G31
G20
SWEDEN (SE)
II2H3B/P
II2H3+
20
28-30, 37
UNITED KINGDOM (UK)
G30, G31
CE Standard
Required airflow for the combustion air supply is 2m3/h per kW.
1. Connect the quick-disconnect hose to the fryer quick-disconnect fitting under the front of the
fryer and to the building gas line.
NOTE: Some fryers are configured for a rigid connection to the gas supply line. These units are
connected to the gas supply line at the rear of the unit.
When using thread compound, use very small amounts on male threads only. Use
a pipe thread compound that is not affected by the chemical action of LP gases
(Loctite™ PST56765 Sealant is one such compound). DO NOT apply compound
3-6
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
to the first two threads. Doing so may allow some of the compound to enter the
gas stream, resulting in clogging of burner orifices and/or the control valve.
2. Open the gas supply to the fryer and check all piping, fittings, and gas connections for leaks with
a leak detection fluid.
3. Close the fryer drain valve and fill the frypot with water and boil-out solution to the bottom
OIL LEVEL line at the rear of the frypot. Light the fryer and perform the boil-out procedures
that are described in the “Lighting Instructions” and “Boiling Out the Frypot” topics found in
Chapter 3 of this manual.
DANGER
“Dry-firing” your unit will cause damage to the frypot and can cause a fire. Always
ensure that melted shortening, cooking oil, or water is in the frypot before firing your
unit.
4. The burner manifold pressure should be checked at this time by the local gas company or an
authorized service agent. The tables below and on the following page list the burner manifold gas
pressures for the various gas types that can be used with this equipment.
5. Check the programmed temperature or solid-state (analog) controller thermostat setting. (Refer
to the separate Frymaster Fryer Controllers User’s Manual furnished with your unit for the
setpoint programming instructions for your particular controller.)
3.6 Converting to Another Gas Type
DANGER
This appliance was configured at the factory for a specific type of gas. Converting
from one type of gas to another requires the installation of specific gas-conversion
components.
Switching to a different type of gas without installing the proper conversion
components may result in fire or explosion. NEVER ATTACH THIS APPLIANCE TO A
GAS SUPPLY FOR WHICH IT IS NOT CONFIGURED!
Conversion of this appliance from one type of gas to another should only be
performed by qualified, licensed, and authorized installation or service personnel, as
defined in Section 1.7 of this manual.
CE Gas Conversion Kits
826-2937(1814 vats); 826-2939 (HD50 vats) — Natural to Propane
826-2938 (1814 vats); 826-2940 (HD50 vats) — Propane to Natural
3-7
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
CE GAS CONVERSION INSTRUCTIONS
1. Between G20- and G25-type Natural Gas, adjust the gas pressure at the regulator. (Refer to the
CE Standard Burner Manifold Gas Pressure Chart.) Do not change the orifice.
2. Between a 2nd family (G20 or G25) and a 3rd family gas (G30 Butane or G31 Propane):
a. Change the orifices.
b. Adjust the manifold pressure.
3. Affix the new label included with the conversion kit next to the existing rating plate stating that
the gas type has been converted. Remove any references to the previously used gas from the
existing rating plate.
Conversions can only be executed by qualified, factory-authorized personnel.
Pilot pressure adjustment
(remove cover screw to
access)
Pressure flow adjustment
(remove cover screw to
access)
Regulator Vent
Pilot gas supply
connection.
ON/OFF
Gas-Cock Knob
Typical non-CE gas valve for electronic-ignition equipped fryers.
3-8
Frymaster BK1814 Series Gas Fryers
Chapter 3: Installation
3.7 Electrical Connections
The fryer when installed must be electrically grounded in accordance with local codes, or in the
absence of local codes, with the National Electrical Code, ANSI/NFPA 70-(latest edition).
DANGER
This fryer is equipped with a three-prong (grounding) plug for protection against
electrical shock and must be plugged directly into a properly grounded, three-prong
receptacle. DO NOT CUT, REMOVE, OR OTHERWISE BYPASS THE GROUNDING
PRONG ON THIS PLUG!
The rating plate and wiring diagram are located inside the front door. The fryer is equipped with a
120VAC single-phase 60-hertz system (Domestic), or 230VAC single-phase 50-hertz system
(International/CE). Do not cut or remove the ground prong from the power cord plug. Do not
attempt to use the fryer during a power outage.
DANGER
This appliance requires electrical power for operation. Place the gas control valve in
the OFF position in case of a prolonged power outage. Do not attempt to operate
this appliance during a power outage.
3-9
Frymaster BK1814 Series Gas Fryers
Chapter 4: Fryer Operations
4.1 Initial Start-up
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil frying system, particularly the aspects of
system operation, oil filtration, draining and cleaning procedures.
Cleaning: New units are wiped clean with solvents at the factory to remove any visible signs of dirt,
oil, grease, etc. remaining from the manufacturing process, then coated lightly with oil. Before any
food preparation, wash thoroughly with hot, soapy water to remove any film residue and dust or
debris then rinse out and wipe dry. Also wash any accessories shipped with the unit. Close the drain
valve completely and remove the crumb screen covering the heating tubes. Ensure the screws
holding the thermostat and high-limit control sensing bulbs into the frypot are tight.
Typical sensor probe/high-limit locations and mounting hardware.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is
present to seal the joint between the frypots. Banging fry baskets on the strip to
dislodge shortening will distort the strip, adversely affecting its fit. It is designed for
a tight fit and should only be removed for cleaning.
DANGER
Never operate this appliance with an empty frypot. The frypot must be filled with
water or oil before lighting the burners. Failure to do so will damage the frypot and
may cause a fire.
4-1
Frymaster BK1814 Series Gas Fryers
Chapter 4: Fryer Operations
4.2 Final Preparation
WARNING
NEVER set a complete block of solid shortening on top of heating tubes. To do so
will damage the heating tubes and frypot, and void the warranty.
4.2.1 Filling Fryer with Oil
A. When using oil, fill the fryer to the bottom OIL LEVEL line scribed into the back of the
frypot.
B. When using a solid shortening, cut it into small pieces and pack it below the heat tubes,
between the tubes and on top of the tubes, leaving no air spaces around the tubes. Do not
disturb or bend the probe sensing bulbs.
C. Press the computer on/off switch to "ON".
D. When the frypot is filled and the oil is heated, carefully replace the crumb screen over the
heat tubes. Wear oil-proof insulated gloves to avoid the potential for burn injury when
placing crumb screen in frypot.
E. DO NOT overheat the oil, which can shorten its life. A high-limit thermostat opens, shutting
off the burners and preventing further heating at 425°F/218°C in domestic units and
212°C/415°F in CE units.
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil filtering system, particularly the aspects
of oil filtration, draining and cleaning procedures.
4.2.2 Pilot Lighting Procedures, Electronic Ignition Systems
Initial Pilot Lighting: All Frymaster fryers are tested, adjusted and calibrated
to sea level conditions before leaving the factory. Adjustments to assure
proper operation of pilot may be necessary on installation to meet local
conditions, low gas pressure, differences in altitude and variations in gas
characteristics. These adjustments correct possible problems caused by rough
handling or vibration during shipment, and are to be performed only by
qualified service personnel. These adjustments are the responsibility of the
customer and/or the dealer and are not covered by the Frymaster warranty.
The inlet pipe at the lower rear of the fryer brings incoming gas to the pilot
safety control valve, then to the pilot and main burners. The pilot is located
high in the cabinet center, at the base of the frypot.
Pilot in normal operation.
4-2
Frymaster BK1814 Series Gas Fryers
Chapter 4: Fryer Operations
WARNING
Never use a match or taper to light pilot on this ignition system.
1. Ensure the frypot is filled to the appropriate line with oil or water.
2. Turn gas "ON".
3. Turn electric power "ON" with the power button on the computer.
4. The ignition module will energize the pilot gas supply and the ignitor. The ignitor spark will
ignite the pilot gas. The presence of the pilot flame is then proved by a flame sensor, which
sends a signal to the main gas supply, opening the valve. The computer controls the fryer after
ignition.
WARNING
In the event of prolonged power failure, the ignition module will shut down and lock
out the system. Turn the unit power "OFF" and then back "ON" after power has been
re-established.
5. If the pilot flame fails, the ignition module will shut down and lock out the system. To restart,
turn the computer "OFF", wait approximately 5 minutes for the system to recycle itself, then turn
the computer "ON" again. Repeat Steps 1-3.
6. See operational instructions in 1814 Computer manual. Do not leave the fryer unattended during
operation.
WARNING
When checking for burner ignition or performance, do not get too close to the
burners. Slow ignition can cause possible flashback, increasing the potential for
facial and body burns.
4-3
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Instructions
WARNING
Drawings and photos used in this manual are intended to illustrate
operational, cleaning and technical procedures and may not conform to on-
site management operational procedures.
WARNING
The on-site supervisor is responsible for ensuring that operators are made
aware of the inherent hazards of operating a hot oil filtering system,
particularly the aspects of oil filtration, draining and cleaning procedures.
5.1 Draining and Manual Filtering
DANGER
Draining and filtering of oil must be accomplished with care to avoid the
possibility of a serious burn caused by careless handling. The oil to be filtered
is at or near 350°F (177°C). Ensure all hoses are connected properly and drain
handles are in their proper position before operating any switches or valves.
Wear all appropriate safety equipment when draining and filtering oil.
DANGER
Allow oil to cool to 100°F (38°C) before draining into an appropriate container
for disposal.
DANGER
Do not drain more than one frypot at a time into the built-in filtration unit to
avoid overflow and spillage of hot oil.
DANGER
When draining oil into a disposal unit or portable filter unit, do not fill above the
maximum fill line located on the container.
If your fryer is not equipped with a built-in filtration system, the oil must be drained into
another suitable container. (For safe, convenient draining and disposal of used oil, Frymaster
recommends using the Frymaster Shortening Disposal Unit (SDU). The SDU is available
through your local distributor.)
1. Turn the fryer power switch to the OFF position. Screw the drainpipe (provided with
your fryer) into the drain valve. Make sure the drainpipe is firmly screwed into the drain
valve and that the opening is pointing down.
2. Position a metal container with a sealable cover under the drainpipe. The metal container
must be able to withstand the heat of the oil and hold hot liquids. If you intend to reuse
the oil, Frymaster recommends that a Frymaster filter cone holder and filter cone be used
when a filter machine is not available. If you are using a Frymaster filter cone holder, be
sure that the cone holder rests securely on the metal container.
5-1
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
3. Open the drain valve slowly to avoid splattering. If the drain valve becomes clogged with
food particles, use the Fryer’s Friend (poker-like tool) to clear the blockage.
DANGER
NEVER attempt to clear a clogged drain valve from the front of the valve! Hot
oil will rush out creating the potential for severe burns.
DO NOT hammer on the drain valve with the cleanout rod or other objects.
Damage to the ball inside will result in leaks and will void the Frymaster
warranty.
4. After draining the oil, clean all food particles and residual oil from the frypot. BE
CAREFUL, this material may still cause severe burns if it comes in contact with bare skin.
5. Close the drain valve securely and fill the frypot with clean, filtered or fresh oil or solid
shortening to the bottom OIL-LEVEL line.
DANGER
WHEN USING SOLID SHORTENING, PACK THE SHORTENING DOWN IN
BETWEEN THE TUBES TO THE BOTTOM OF THE FRYPOT. DO NOT OPERATE
THE FRYER WITH A SOLID BLOCK OF SHORTENING SITTING IN THE UPPER
PORTION OF THE FRYPOT. THIS WILL CAUSE DAMAGE TO THE FRYPOT
AND MAY CAUSE A FLASH FIRE.
5.2 General Filtration Information
Most filter systems use filter paper as the filter medium. Filter powder is required to enhance
the filtration process. Photos used in the procedural illustrations may differ from the filter
unit that came with the frying system. The following procedures apply to all fryers equipped
with filter systems. Filter system design depends on the frying system configuration.
5.3 Filter Preparation
On initial installation and before each use, clean the filter:
a. Remove all loose parts from the filter,
b. Wash the filter pan and all accessories in hot, soapy water,
c. Dry thoroughly.
5-2
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.3.1 Filter Components
Filter paper is held in place by a hold-down ring. Oil moves through the paper, leaving behind
impurities.
1. Filter pan.
2. Filter support grid.
3. Filter paper.
4. Hold-down ring.
5. Crumb screen.
A filter unit which utilizes disposable
filter paper to filter oil.
5-3
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.3.2 Assembling the Filter
1. Place the support grid in the bottom of
filter pan.
Support grid properly placed in filter pan.
Ensure filter paper overlaps two inches on all
sides and is evenly distributed under the hold-
down ring.
2. Put one filter paper sheet on top of the
support grid. Be sure the paper covers the
filter pan bottom and laps two inches onto
the pan wall.
3. Position the hold-down ring on top of the
filter paper. Ensure the hold-down ring
seals around the support grid.
This
prevents sediment from getting into the
system.
Hold-down ring positioned correctly over filter
paper in filter pan.
5-4
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.3.2 Assembling the Filter (cont.)
4. Sprinkle 8 ounces (227g) of filter powder on
the filter sheet. Ensure the powder covers the
filter paper evenly.
Sprinkle the proper amount of filter powder evenly
over the paper.
5. Place the crumb screen in the filter pan.
Allow the crumb screen to rest on the top
edges of the hold-down ring.
Crumb screen properly placed.
6. Return filter pan to cabinet.
5-5
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.3.3 Installing the Filter
1. Slide the filter inside the fryer cabinet. Ensure the male-female pickup tubes are fully engaged.
Ensure the filter pan opening is directly under the center dump tube.
The filter pan slides under
the fryer (left), connecting
with a male connector (right).
Ensure that the pickup tube
is securely coupled with this
connector. Its location may
vary based on model.
5.4 Daily Filter Operation
WARNING
Use caution and wear proper protective clothing. The oil to be filtered is at or near
350°F (177°C). Ensure all hoses are connected properly and drain handles are in
their proper position prior to operating any switches or valves. Failure to do this can
result in severe burns.
WARNING
Drawings and photos used in this manual are intended to illustrate operational,
cleaning and technical procedures and may not conform to on-site management
operational procedures.
5.4.1 General Overview
Only filter oil at operating temperature (~350°F/~177°C). When filtering begins, the filter motor
engages and oil is drawn through filter paper or a filter-leaf assembly and pumped back into the
frypot through oil return plumbing. The frypot’s drain remains open during the filtering process,
allowing oil to filter through the frypot and back into the filter unit. Allow the oil to cycle through
this process for approximately 5 minutes. At the end of 5 minutes, close the drain valve and allow
the frypot to fill to the top OIL LEVEL line. Leave the pump running for 10-15 seconds after
bubbles appear in the frypot to ensure all oil is pumped from the drain pan and the lines. Close the
oil return valve.
5-6
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.4.2 Filtering Tools
Assemble tools to be used for filtering. These are supplied with the filter starter kit included with
the fryer/filter system:
•
Frypot/Filter Brush - used to clean frypot and filter pan sides and bottom, heating elements,
and to dislodge sediment during filtration or oil change.
•
•
•
Clean-out Rod (design may vary) - used to dislodge heavy debris in the drain tube (when needed).
Filter Powder.
Filter Paper.
The following tools are not required, but are recommended to make the filtering task easier.
•
•
Measuring Cup - used to measure filter powder.
Stainless Steel Crumb Scoop - for removing large debris from oil prior to filtering.
Note: Always wear oil-resistant, insulated gloves and/or protective gear when
working with hot oil.
5-7
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.5 Operating the Filter
5.5.1 Pan Preparation and Operation
See Section 5.3.2, Assembling the Filter, and Section 5.3.3, Installing the Filter, for the appropriate
filter preparation procedure.
CAUTION
NEVER operate the filter unit unless cooking oil is at operating temperature (~350°F/
~177°C).
1. Ensure the filter pan assembly is prepared as described in Section 5.3.2, Assembling the Filter,
and ensure fryer is turned off.
2. Remove fry baskets from frypot and skim any
large debris from the oil. Use extreme
caution, as oil is at or near operating
temperature (~350°F/~177°C).
Prior to filtering, skim any large debris from oil in
frypot.
3. Remove the support grid from the frypot
using the clean-out rod. Stir the oil with the
frypot/filter brush to suspend debris prior to
draining.
Removing support grid from fry vessel prior to
filtering.
5-8
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.5.1 Pan Preparation and Operation (cont.)
4. After ensuring the filter pan is correctly
positioned under the drain tubes, move the
red handle to the open position (right) to
drain the frypot into the filter pan. Drain
ONLY ONE frypot at a time. The filter
pan is designed to hold the contents of one
frypot only.
Move the red drain valve handle into the open
position.
5. After all oil has drained from the frypot into
the filter pan, turn the yellow handle to open
the oil return lines and activate the filter
pump. Leave the red handle in the open
position.
Turn the yellow handle to open the oil return valve
and activate the filter pump.
5-9
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.5.2 Filter Operation
6. Oil will begin to pump from the filter pan
into the frypot. If the frypot tubes, sides and
bottom have sediment deposits, clean the
frypot with the cleaning brush included with
the fryer. Clean beneath and under the burner
tubes, using care not to disturb the probes
(arrow).
Clean all sediment and suspended particles from
the burner tubes and frypot as the oil begins to
circulate. Use care not to disturb the probes
(arrow) on the burner tube.
7. Allow the oil to circulate for approximately 5
minutes (process known as "polishing") to
remove suspended particles.
Polishing the oil removes suspended particles,
which increases the life of the oil.
8. After the filter cycle is complete, close the
drain valve (push the red handle to the left
until it stops) and allow the fryer to refill (see
Step 4 above for additional reference).
After filtering is complete, close the red drain
handle to start refilling the frypot.
5-10
Frymaster BK1814 Series Gas Fryers
Chapter 5: Filtration Operation
5.5.2 Filter Operation (cont.)
9. After all oil is pumped back into the frypot,
bubbles will form, indicating air in the oil
return lines. Allow the oil to bubble for 10-
15 seconds to ensure all oil is evacuated
from the return lines. Turn the yellow
handle to close the oil return valve and
deactivate the filter pump (see Step 5 above
for additional reference).
Allow the oil to bubble for 10-15 seconds to
ensure evacuation of all oil in the return lines.
10. If the oil level is low, add oil until the level
is at the top OIL LEVEL line.
DO NOT OVERFILL THE FYPOT. This
will cause oil to splash out of the
frypot during cooking and may
cause burns or damage.
Add oil until the oil level is at the top OIL LEVEL
line. DO NOT OVERFILL THE FRYPOT.
11. Replace the frypot grid, using care not to
splash hot oil. Turn the fryer on.
Replace the frypot grid, using care not to splash
hot oil.
5-11
FRYMASTER 1814 SERIES GAS FRYERS
CHAPTER 5: FILTRATION INSTRUCITONS
5.5.2 Filter Operation (cont.)
12. Do not allow crumbs to accumulate in the
crumb tray. The crumb tray MUST be
emptied into a fireproof container at the end
of frying operations EACH DAY (see
DANGER statement below).
Empty the filter pan crumb tray into a fire-proof
container at the end of frying operations each day.
DO NOT ALLOW CRUMBS TO ACCUMULATE IN
TRAY.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a
fireproof container at the end of frying operations each day. Some food particles
can spontaneously combust if left soaking in certain shortening material.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is
present to seal the joint between the fry vessels. Banging fry baskets on the strip to
dislodge shortening will distort the strip, adversely affecting its fit. It is designed for
a tight fit and should only be removed for cleaning.
WARNING
The filter pump is equipped with a manual reset switch in case the filter motor
overheats or an electrical fault occurs. If this switch trips, turn off power to the filter
system and allow the pump motor to cool 20 minutes before attempting to reset the
switch (see photo below).
Filter Pump Reset Switch
5-12
Frymaster BK1814 Series Gas Fryers
Chapter 6: Preventive Maintenance
6.1 General
DANGER
Never attempt to clean the fryer during the cooking process or when the frypot is
filled with hot oil. If water comes in contact with oil heated to cooking temperature, it
will cause spattering of the oil, which can result in severe burns to nearby personnel.
Any equipment works better and lasts longer when maintained properly and kept clean. Cooking
equipment is no exception. Frymaster 1814 Series gas fryers should be kept clean during the
working day, and thoroughly cleaned at the end of each day. Below are recommendations for daily,
weekly and periodic preventative maintenance.
6.1.1 Daily
WARNING
Use a commercial grade cleaner formulated to effectively clean and sanitize food-
contact surfaces. Read the directions and precautionary statements for use.
Particular attention must be paid to the concentration of cleaner and the length of
time the cleaner remains on the food-contact surfaces.
A. Remove and wash all removable parts.
B. Clean all exterior surfaces of the cabinet. Do not use cleaners, steel wool, or any other
abrasive material on stainless steel.
C. Filter the cooking oil and replace if necessary. The oil should be filtered more frequently
when under heavy use.
D. Clean filter pan, as well as, crumb tray as discussed on page 5-1.
6.1.2 Weekly
A. Completely drain the oil from the fryer into a metal stockpot of sufficient size to safely hold
the entire contents of the frypot for disposal. Do not use a glass or plastic container.
B. Clean the frypot.
6-1
Frymaster BK1814 Series Gas Fryers
Chapter 6: Preventive Maintenance
6.1.3 Periodic/ Annual
The fryer should be inspected and adjusted periodically by qualified service personnel as part
of a regular kitchen maintenance program.
Frymaster recommends that the fryer be inspected at least annually by a Factory Authorized
Service technician as follows:
• Inspect fryer cabinet inside and out, front and rear, for excessive oil build-up. Verify that
burners and associated components (i.e. gas valves, pilot assemblies, ignitors, etc.) are in good
condition and functioning properly. Inspect all gas connections for leaks and ensure all
connections are properly tightened.
• Verify that temperature and high-limit probes are properly connected, tightened and functioning
properly.
• Verify all component box components (i.e. computer/controller, relays, transformers, interface
boards, etc.) are in good condition and free from oil build-up and other debris. Inspect
component box wiring and ensure all connections are tight and all wiring is in good condition.
Ensure all safety features (i.e. drain safety switches, reset switches, etc.) are present and
functioning properly.
• Verify that frypot is in good condition and free of leaks. Verify that frypot tube diffusers are
present and in good condition (i.e. no visible deterioration or damage).
• Verify that all wiring and connections are tight and in good condition.
Built-in Filtration:
• Inspect all oil-return and drain lines for leaks and verify that all connections are tight.
• Inspect the filter pan for leaks and cleanliness. If there is a large accumulation of crumbs in the
crumb basket, advise the owner/operator that the crumb basket should be emptied into a fireproof
container and cleaned daily.
• Verify that all O-rings and seals (including those on quick-disconnect fittings) are present and in
good condition. Replace O-rings and seals if worn or damaged.
6-2
Frymaster BK1814 Series Gas Fryers
Chapter 6: Preventive Maintenance
6.1.3 Periodic/ Annual (cont.)
• Check filtration system integrity as follows:
− With the filter pan empty, place each oil return handle, one at a time, in the "ON" position.
Verify that the pump activates and that bubbles appear in the oil of the associated frypot.
− Close all oil return valves (i.e., place all oil return handles in the "OFF" position). Verify proper
functioning of each oil return valve by activating the filter pump using the lever on one of the oil
return handle microswitches. No air bubbles should be visible in any other frypot.
− Verify that the filter pan is properly prepared for filtering, then drain a frypot of oil heated to
350°F (177°C) into the filter pan and close the frypot drain valve. Place the oil return handle in
the "ON" position. Allow all oil to return to the frypot (indicated by bubbles in the oil. Return
the oil return handle to the "OFF" position. The frypot should refill in no more than 2 minutes
and 30 seconds.
To ensure good fryer health and a safe environment, the fryer should be checked and adjusted
periodically by qualified service personnel as part of a regular kitchen maintenance program.
6.1.4 Stainless Steel Care
DANGER
DO NOT let water splash into the tank of hot oil. It will splatter and can cause severe
burns.
All stainless steel fryer cabinet parts should be wiped regularly with hot, soapy water during the day,
and with a liquid cleanser designed for stainless steel at the end of each day.
A. Do not use steel wool, abrasive cloths, cleansers or powders.
B. Do not use a metal knife, spatula or any other metal tool to scrape stainless steel! Scratches
are almost impossible to remove.
C. If it is necessary to scrape the stainless steel to remove any encrusted materials, soak the area
first to soften the deposit, then use a wood or nylon scraper only.
6-3
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.1 General
DANGER
Hot oil will cause severe burns. Never attempt to move this appliance when filled
with hot oil or to transfer hot oil from one container to another.
DANGER
This equipment should be unplugged when servicing, except when electrical circuit
tests are required. Use extreme care when performing such tests.
This appliance may have more than one electrical power supply connection point.
Disconnect all power cords before servicing.
Inspection, testing and repair of electrical components should be performed by an
authorized service agent only.
The problems and possible solutions covered are those most commonly encountered. To
troubleshoot, perform the test set-up at the beginning of each condition. Follow each step in
sequence.
7.2 Pilot Burner Malfunction
A. Pilot will not ignite; no evidence of gas at pilot burner.
1. Check that gas valve is open and gas is present at the gas valve.
2. Check pilot burner orifice for dirt or lint.
3. Authorized Service Agent Only: Remove pilot burner gas-supply line and check for
contamination; blow out if necessary, then reinstall.
B. Pilot burner ignites but will not remain lit when gas valve manual knob is released.
1. Check that thermopile lead is properly connected at the terminal block on the gas valve.
2. Authorized Service Agent Only: Pilot flame may be too high or too low. Adjust pilot
flame adjustment screw so that pilot flame extends about 3/4-inch (19-mm) above the top
of the pilot burner.
7-1
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.2 Pilot Burner Malfunction (cont.)
3. Check all connections for cleanliness and security.
C. Pilot flame of proper size, but is unstable. Flame wavers and does not envelop the
thermopile completely at all times.
1. Check for drafts that might be caused by air conditioning equipment or make-up air
apparatus. Turn air-moving equipment off and recheck the pilot.
7.3 Main Burner Malfunctions
A. Main burner will not come "ON"; gas not detected at main burner.
1. Check that the gas valve is open.
2. Check that the pilot is ignited and is operating properly.
3. Authorized Service Agent Only: Check the high-limit switch for continuity.
4. Authorized Service Agent Only: Check the combination gas valve and replace if
defective.
B. Main burner flames are small and appear lazy; oil does not come up to temperature quickly.
1. Authorized Service Agent Only: Check gas pressure at the pressure tap of the gas valve.
Use dial type or standard water-type U-gauge manometer. With burner in operation, the
pressure should be 4" W.C. (10 mbar) for natural gas, and 11" W.C. (27.5 mbar) for
propane. If not, remove the pressure regulator adjustment cover. Use screwdriver to
turn the adjusting screw for proper pressure. Replace cover, re-check pressure and re-
install pressure tap plug.
C. Signs of excessive temperature; oil scorches and quickly becomes discolored.
1. Check operating thermostat. May be out of adjustment or calibration. Recalibrate if
necessary.
2. Check gas pressure as outlined above.
3. Oil used is of inferior quality and/or oil has been used too long. Replace oil.
4. Ensure frypot is clean when refilling with new oil.
7-2
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.3 Main Burner Malfunctions (cont.)
D. Fryer will not reach the temperature setting and/or runs erratically.
1. Incorrect location of sensor probe or defective temperature sensor.
2. Loose wiring/wire connection
E. Fryer oil temperature cannot be controlled; fryer runs at high-limit temperature.
1. Defective temperature probe; Call Authorized Service Agent.
User- Replaceable Parts
Descripton
Part Number
803-0380
108-1872
823-7619
803-0278
803-0197
823-7770
823-7771
823-7772
823-7773
823-7774
823-7895
106-4309
210-8077
810-1105
Filter Pan Components
823-7425
810-3541
200-8003
823-7294
810-2805
803-0289
Basket Rack, 16x13.7
Vat cover 21.38 x 19.43
Splash guard
L-shaped brush
Fryers’ friend
Basket hanger (single and used with RAM unit left or right)
Basket hanger, two battery, larger 1814 pots
Basket hanger, three battery, smaller pot in middle
Basket hanger, two battery with larger 1814 pot left
Basket hanger, two battery unit with larger 1814 pot on right
Single pot, non-filter unit
Door, left or right
Door handle
Door magnet
Crumb tray
Hold-down ring
Sana grid screen
Filter pan
Caster
Filter paper
7-3
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.4 Wiring Diagrams,
7.4.1 Main for all models after Sep. 2010
7-4
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.4.2 Main for all models prior to Sep. 2010
7-5
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.4.3 CE Wiring Diagram
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.5 Wiring Diagram, Filter
7-7
Frymaster BK1814 Series Gas Fryers
Chapter 7: Troubleshooting
7.6 Wiring Diagram, RAM Units Only
7-8
Frymaster, L.L.C., 8700 Line Avenue, Shreveport, Louisiana 71106
TEL 1-318-865-1711
FAX (Parts) 1-318-688-2200
FAX (Tech Support) 1-318-219-7135
819-6557
MAR 2011
SERVICE HOTLINE
1-800-551-8633
PRINTED IN THE UNITED STATES
|