SERVICE AND PARTS MANUAL
FRYMASTER BIELA14 SERIES GEN II
LOV™ ELECTRIC FRYER
This equipment chapter is to be
installed in the Fryer Section of the
Equipment Manual.
FOR YOUR SAFETY
Do Not Store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
MANUFACTURED
BY
8700 Line Avenue
SHREVEPORT, LOUISIANA 71106
PHONE: 1-318-865-1711
TOLL FREE: 1-800-551-8633
1-800-24 FRYER
FAX: 1-318-688-2200
Frymaster L.L.C., 8700 Line Avenue, Shreveport, LA 71106
PHONE 318-865-1711 FAX 318-219-7135
PRINTED IN THE UNITED STATES
SERVICE HOTLINE
1-800-24-FRYER
MAY 2011
email: [email protected]
* 8 1 9 6 4 4 6 *
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS
MANITOWOC FOOD SERVICE EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR
RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS
AUTHORIZED SERVICE CENTERS, AND OR THE PART BEING USED IS MODIFIED FROM
ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER, FRYMASTER
DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS, DAMAGES OR
EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN
WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART
RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER.
NOTICE
This appliance is intended for professional use only and is to be operated by qualified
personnel only. A Frymaster Dean Authorized Service Agency (ASA) or other qualified
professional should perform installation, maintenance, and repairs.
Installation,
maintenance, or repairs by unqualified personnel may void the manufacturer’s warranty.
NOTICE
This equipment must be installed in accordance with the appropriate national and local
codes of the country and/or region in which the appliance is installed.
DANGER
All wiring connections for this appliance must be made in accordance with the wiring
diagrams furnished with the equipment. Wiring diagrams are locted on the inside of the
fryer door.
NOTICE TO U.S. CUSTOMERS
This equipment is to be installed in compliance with the basic plumbing code of the
Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service
Sanitation Manual of the U.S. Food and Drug Administration.
NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS
U.S.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: 1) This device may not cause harmful interference, and 2) This device must
accept any interference received, including interference that may cause undesired
operation. While this device is a verified Class A device, it has been shown to meet the
Class B limits.
CANADA
This digital apparatus does not exceed the Class A or B limits for radio noise emissions as
set out by the ICES-003 standard of the Canadian Department of Communications.
Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de
classe A et B prescrites dans la norme NMB-003 edictee par le Ministre des Communcations
du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
Improper installation, adjustment, maintenance or service, and unauthorized alterations or
modifications can cause property damage, injury, or death. Read the installation, operating,
and service instructions thoroughly before installing or servicing this equipment.
i
DANGER
The front ledge of this appliance is not a step! Do not stand on the appliance. Serious
injury can result from slips or contact with the hot oil.
DANGER
Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or
any other appliance.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a fireproof
container at the end of frying operations each day. Some food particles can spontaneously
combust if left soaking in certain shortening material.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to
seal the joint between the fry vessels. Banging fry baskets on the strip to dislodge
shortening will distort the strip, adversely affecting its fit. It is designed for a tight fit and
should only be removed for cleaning.
i
DANGER
Adequate means must be provided to limit the movement of this appliance without
depending on or transmitting stress to the electrical conduit. A restraint kit is provided with
the fryer. If the restraint kit is missing contact your local Frymaster Authorized Service
Agency (ASA) for part number 826-0900.
DANGER
This fryer may have two power cords and prior to movement, testing, maintenance and any
repair on your Frymaster fryer; disconnect all electrical power cords from the electrical
supply.
WARNING
Do not use water jets to clean this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
LOV™ ELECTRIC WARRANTY STATEMENT
Frymaster, L.L.C. makes the following limited warranties to the original purchaser only for this
equipment and replacement parts:
A. WARRANTY PROVISIONS - FRYERS
1. Frymaster L.L.C. warrants all components against defects in material and workmanship for a
period of two years.
2. All parts, with the exception of the frypot, O-rings and fuses, are warranted for two years
after installation date of fryer.
3. If any parts, except fuses and filter O-rings, become defective during the first two years after
installation date, Frymaster will also pay straight-time labor costs up to two hours to replace
the part, plus up to 100 miles/160 km of travel (50 miles/80 km each way).
B. WARRANTY PROVISIONS - FRYPOTS
The frypot has a lifetime parts and labor warranty. If a frypot develops a leak after installation,
Frymaster will replace the frypot, allowing up to the maximum time per the Frymaster time
allowance chart hours of straight-time labor. Components attached to the frypot, such as the
high-limit, probe, gaskets, seals, and related fasteners, are also covered by the lifetime warranty
if replacement is necessitated by the frypot replacement. Leaks due to abuse or from threaded
fittings such as probes, sensors, high-limits, drain valves or return piping are not included.
C. PARTS RETURN
All defective in-warranty parts must be returned to a Frymaster Authorized Factory Service
Center within 60 days for credit. After 60 days, no credit will be allowed.
D. WARRANTY EXCLUSIONS
This warranty does not cover equipment that has been damaged due to misuse, abuse, alteration,
or accident such as:
• improper or unauthorized repair (including any frypot which is welded in the field);
• failure to follow proper installation instructions and/or scheduled maintenance procedures as
prescribed in your MRC cards. Proof of scheduled maintenance is required to maintain the
warranty;
• improper maintenance;
• damage in shipment;
• abnormal use;
• removal, alteration, or obliteration of either the rating plate or the date code on the heating
elements;
• operating the frypot without shortening or other liquid in the frypot;
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
• no fryer will be warranted under the ten-year program for which a proper start-up form has not
been received.
This warranty also does not cover:
• transportation or travel over 100 miles/160 km (50 miles/80 km each way), or travel over two
hours;
• overtime or holiday charges;
• consequential damages (the cost of repairing or replacing other property which is damaged), loss
of time, profits, use or any other incidental damages of any kind.
There are no implied warranties of merchantability or fitness for any particular use or purpose.
This warranty is applicable at the time of this printing and is subject to change.
ELECTRICAL POWER SPECIFICATIONS
AMPS PER LEG
WIRE
SERVICE
MIN.
SIZE
AWG
VOLTAGE
PHASE
(mm2)
L1
L2
L3
208
3
3
3
3
4
4
4
6
6
8
6
6
6
(16)
(16)
(10)
(16)
(16)
(16)
39
39
39
240
3
3
3
3
3
34
17
21
20
21
34
17
21
20
21
34
17
21
21
21
480
220/380
240/415
230/400
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
BIELA14 SERIES GEN II LOV™ ELECTRIC FRYERS
TABLE OF CONTENTS
CAUTIONARY STATEMENTS........................................................................................................................................i
WARRANTY STATEMENT ............................................................................................................................................ii
ELECTRICAL POWER SPECIFICATIONS............................................................................................................... iii
CHAPTER 1: Service Procedures
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
General...........................................................................................................................................................1-1
Replacing a Computer....................................................................................................................................1-1
Replacing Component Box Components .......................................................................................................1-1
Replacing a High-Limit Thermostat ..............................................................................................................1-3
Replacing a Temperature Probe.....................................................................................................................1-3
Replacing a Heating Element.........................................................................................................................1-5
Replacing Contactor Box Components..........................................................................................................1-7
Replacing a Frypot.........................................................................................................................................1-8
Built-In Filtration System Service Procedures.............................................................................................1-10
1.9.1
1.9.2
1.9.3
Filtration System Problem Resolution........................................................................................1-10
Replacing the Filter Motor, Filter Pump and Related Components ...........................................1-11
Replacing the Filter Transformer or Filter Relay.......................................................................1-13
1.10 ATO (Automatic Top-Off) Service Procedures ...........................................................................................1-13
1.10.1
1.10.2
1.10.3
1.10.4
ATO Troubleshooting ................................................................................................................1-14
ATO Board Pin Positions and Harnesses...................................................................................1-15
Replacing the ATO board, LON Gateway, ATO pump relay or Transformer...........................1-16
Replacing the ATO Pump ..........................................................................................................1-16
1.11 MIB (Manual Interface Board) Service Procedures.....................................................................................1-16
1.11.1
1.11.2
1.11.3
1.11.4
1.11.5
1.11.6
1.11.7
Manually Draining, Refilling or Filtering with the MIB Board .................................................1-17
MIB Troubleshooting.................................................................................................................1-18
MIB Pin Positions and Harnesses ..............................................................................................1-20
MIB Display Diagnostics...........................................................................................................1-21
MIB Display Characters.............................................................................................................1-22
Replacing the MIB board ...........................................................................................................1-22
Control Power Reset Switch.......................................................................................................1-22
1.12 RTI Service Issues .......................................................................................................................................1-23
1.12.1
1.12.2
1.12.3
1.12.4
RTI MIB Tests ...........................................................................................................................1-23
RTI LOV Wiring........................................................................................................................1-24
RTI Plumbing Schematic ...........................................................................................................1-24
RTI LOV Quick Reference ........................................................................................................1-25
1.13 AIF (Automatic Intermittent Filtration) Service Procedures........................................................................1-27
1.13.1
1.13.2
1.13.3
1.13.4
AIF Troubleshooting..................................................................................................................1-27
AIF Actuator Board Pin Positions and Harnesses......................................................................1-28
Replacing an AIF Board.............................................................................................................1-29
Replacing an Actuator................................................................................................................1-29
1.14 M3000 Computer Service Procedures..........................................................................................................1-30
1.14.1
1.14.2
1.14.3
1.14.4
1.14.5
1.14.6
1.14.7
1.14.8
M3000 Computer Troubleshooting............................................................................................1-30
M3000 Useful Codes and Passwords .........................................................................................1-33
Service Required Errors .............................................................................................................1-34
Error Log Codes.........................................................................................................................1-35
Tech Mode .................................................................................................................................1-36
M3000 Filter Error Flowchart....................................................................................................1-37
M3000 Menu Summary Tree .....................................................................................................1-38
M3000 Board Pin Positions and Harnesses................................................................................1-39
1.15 Loading and Updating Software Procedures................................................................................................1-40
1.16 Data Network Flowchart..............................................................................................................................1-41
1.17 Interface Board Diagnostic Chart.................................................................................................................1-42
1.18 Probe Resistance Chart ................................................................................................................................1-43
1.19 Wiring Diagrams..........................................................................................................................................1-44
1.19.1
1.19.2
Component Wiring Domestic.....................................................................................................1-44
Component Wiring CE...............................................................................................................1-45
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
BIELA14 SERIES GEN II LOV™ ELECTRIC FRYERS
TABLE OF CONTENTS cont.
1.19.3
1.19.4
1.19.5
1.19.6
1.19.7
1.19.8
1.19.9
Component Wiring CSA............................................................................................................1-46
Component Wiring Australia .....................................................................................................1-47
Contactor Box-Delta Configuration...........................................................................................1-48
Contactor Box-WYE Configuration...........................................................................................1-49
Simplified Full-Vat Delta Wiring ..............................................................................................1-50
Simplified Dual-Vat Delta Wiring .............................................................................................1-51
Simplified Full-Vat Export WYE Wiring ..................................................................................1-52
1.19.10 Simplified Dual-Vat Export WYE Wiring.................................................................................1-53
1.19.11 Simplified LOV Wiring .............................................................................................................1-54
CHAPTER 2: Parts List
2.1
2.2
2.3
Accessories ....................................................................................................................................................2-1
Doors, Sides, Tilt Housings, Cap N Splash, Top Caps and Casters...............................................................2-2
Drain System Components.............................................................................................................................2-3
2.3.1
2.3.2
Drain Tube Sections and Associated Parts...................................................................................2-3
Drain Valves and Associated Parts ..............................................................................................2-4
2.4
Electronics and Electrical Components .........................................................................................................2-5
2.4.1
2.4.2
2.4.3
Component Boxes........................................................................................................................2-5
Contactor Boxes...........................................................................................................................2-7
Heating Element Assemblies and Associated Parts .....................................................................2-9
2.4.3.1 Element Assemblies and Hardware..............................................................................2-9
2.4.3.2 Element Tube Assemblies..........................................................................................2-11
Computers..................................................................................................................................2-12
Wiring ........................................................................................................................................2-13
2.4.5.1 Contactor Box Wiring Assemblies 12-Pin Dual Vat..................................................2-13
2.4.5.2 Contactor Box Wiring Assemblies 12-Pin Full Vat ...................................................2-13
2.4.5.3 Contactor Box Wiring Assemblies 6-Pin Left Element .............................................2-14
2.4.5.4 Contactor Box Wiring Assemblies 9-Pin Right Element ...........................................2-14
2.4.5.5 Main Wiring Harnesses..............................................................................................2-15
2.4.5.6 Component Box and Filter Pump Wiring Harnesses..................................................2-16
2.4.5.7 Interface Board to Controller Wiring Harness 15-Pin................................................2-16
2.4.5.8 M3000, MIB, AIF and ATO Wiring Harnesses.........................................................2-17
2.4.4
2.4.5
2.5
Filtration System Components.....................................................................................................................2-18
2.5.1
2.5.2
Filtration Components..................................................................................................................2-18
Auto Intermittent Filtration Components.....................................................................................2-20
2.5.2.1 LOV Indicator Lights Assembly ................................................................................2-20
2.5.2.2 Manual Interface Board Assembly.............................................................................2-20
2.5.2.3 AIF Linear Actuator Board Assembly .......................................................................2-21
2.5.2.4 LOV PCB Board Matrix ............................................................................................2-21
2.6
2.7
2.8
2.9
Frypot Assemblies and Associated Components .........................................................................................2-22
Oil Return Manifolds ...................................................................................................................................2-24
Return Valves and Associated Parts ............................................................................................................2-24
Auto Top Off Components ..........................................................................................................................2-25
2.9.1
2.9.2
2.9.3
2.9.4
2.9.5
JIB Basket ....................................................................................................................................2-25
JIB Cap and Pick Up Assembly...................................................................................................2-25
Automatic Top Off Board Assembly ...........................................................................................2-26
ATO Pump Assembly ..................................................................................................................2-27
ATO Pump Assembly Service Kit (Larger Top Off Lines) .........................................................2-28
2.10 RTI................................................................................................................................................................2-29
2.10.1
2.10.2
RTI Manifold and Accessories.....................................................................................................2-29
RTI Dispose Waste Valve............................................................................................................2-31
2.10.3 RTI test Box.................................................................................................................................2-31
2.11 Wiring Connectors, Pin Terminals and Power Cords ..................................................................................2-32
2.12 Fasteners ......................................................................................................................................................2-33
v
Download from Www.Somanuals.com. All Manuals Search And Download.
BIELA14 SERIES GEN II LOV™ ELECTRIC FRYERS
CHAPTER 1: SERVICE PROCEDURES
1.1 General
Before performing any maintenance on your Frymaster fryer, disconnect the fryer from the electrical
power supply.
WARNING
To ensure the safe and efficient operation of the fryer and hood, the electrical plug for
the 120-volt line, which powers the hood, must be fully engaged and locked in its pin
and sleeve socket.
When electrical wires are disconnected, it is recommended that they be marked in such a way as to
facilitate re-assembly.
1.2 Replacing a Computer
1. Disconnect the fryer from the electrical power supply.
2. The computer bezel is held in place by tabs at the top and bottom. Slide the metal bezel up to
disengage the lower tabs. Then slide the bezel down to disengage the upper tabs.
3. Remove the two screws from the upper corners of the control panel. The control panel is hinged at
the bottom and will swing open from the top.
4. Unplug the wiring harnesses from the connectors on the back of the computer, marking their
position for reassembly, and disconnect the grounding wires from the terminals. Remove the
computer panel assembly by lifting it from the hinged slots in the control panel frame.
Ground Wire Terminal
Ground Wire Terminal
20-Pin Connector
Communication
Harnesses
Locator Wire
5. Install the replacement computer. Reinstall the control panel assembly by reversing steps 1 thru 4.
6. Setup the computer following the instructions on page 4-9 in the Installation and Operation
manual. Setup MUST be performed after replacement.
7. Once setup is complete on all replaced computers, reset all control power following the
instructions in section 1.11.7 on page 1-22 to readdress the new M3000 computer. Check software
version and if necessary update the software. If a software update was necessary, follow the
instructions to update the software in section 1.15
1.3 Replacing Component Box Components
1. Disconnect the fryer from the electrical power supply.
2. The computer bezel is held in place by tabs at the top and bottom. Slide the metal bezel up to
disengage the lower tabs. Then slide the bezel down to disengage the upper tabs.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the two screws from the upper corners of the computer and allow the computer to swing
down.
4. Unplug the wiring harnesses and disconnect the grounding wires from the terminals on the back of
the computer. Remove the computer assembly by lifting it from the hinge slots in the control panel
frame.
5. Disconnect the wiring from the component to be replaced, being sure to make a note of where each
wire was connected.
6. Dismount the component to be replaced and install the new component, being sure that any
required spacers, insulation, washers, etc. are in place.
NOTE: If more room to work is required, the control panel frame assembly may be removed by
removing the hex-head screws which secure it to the fryer cabinet (see illustration below). If this
option is chosen, all computer assemblies must be removed per steps 1 thru 4 above. The cover
plate, on the lower front of the component box, may also be removed to allow additional access if
desired.
Remove these three
screws at each end.
Remove these two screws
from the center supports.
Removing the Control Panel Frame and Top Cap Assembly
7. Reconnect the wiring disconnected in step 5, referring to your notes and the wiring diagrams on
the fryer door to ensure that the connections are properly made. Also, verify that no other wiring
was disconnected accidentally during the replacement process.
8. Reverse steps 1 through 4 to complete the replacement and return the fryer to service.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Replacing a High-Limit Thermostat
1. Remove the filter pan and lid from the unit. Drain the frypots into an McDonald’s Shortening
Disposal Unit (MSDU) or other appropriate METAL container using the computer “drain to pan
option” or using the MIB board in manual mode.
DANGER
DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.
2. Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear of
the fryer.
3. Remove the four screws from both the left and right sides of the lower back panel.
4. Locate the high-limit that is being replaced and follow the two-black wires to the 12-pin connector
C-6. Note where the leads are connected prior to removing them from the connector. Unplug the
12-pin connector C-6 and using a pin-pusher push the pins of the high-limit out of the connector.
5. Carefully unscrew the high-limit thermostat to be replaced.
6. Apply Loctite™ PST 567 or equivalent sealant to the threads of the replacement and screw it
securely into the frypot.
7. Insert the leads into the 12-pin connector C-6 (see illustration below). For full-vat units or the left
half of a dual-vat unit (as viewed from the rear of the fryer) the leads go into positions 1 and 2 of
the connector. For the right half of a dual-vat unit (as viewed from the rear of the fryer), the leads
go into positions 7 and 8. In either case, polarity does not matter.
8. Reconnect the 12-pin connecting plug C-6. Use wire ties to secure any loose wires.
9. Reinstall the back panels, contactor plug guards, reposition the fryer under the exhaust hood, and
reconnect it to the electrical power supply to return the fryer to service.
1.5 Replacing a Temperature Probe
1. Lift the element out of the oil.
2. Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear of
the fryer.
3. Remove the four screws from both sides of the lower back panel. Then remove the two screws on
both the left and right sides of the back of the tilt housing. Lift the tilt housing straight up to
remove from the fryer.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Locate the red (or yellow) and white wires of the temperature probe to be replaced. Note where
the leads are connected prior to removing them from the connector. Unplug the 12-pin connector
C-6 and using a pin-pusher push the pins of the temperature probe out of the connector.
5. Remove the securing probe bracket and metal tie wraps that secure the probe to the element (see
illustration below). Remove the ground clip on the probe shield.
Probe
Leads
Probe
Bracket
Metal Wire Tie
6. Gently pull on the temperature probe and grommet, pulling the wires up the rear of the fryer and
through the element tube assembly.
7. Insert the replacement temperature probe (wires first) into the tube assembly ensuring that the
grommet is in place. Secure the probe to the elements using the bracket which was removed in
Step 5 and the metal tie wraps which were included in the replacement kit.
8. Route the probe wires out of the tube assembly following the element wires down the back of the
fryer through the Heyco bushings to the 12-pin connector C-6. Secure the wires to the sheathing
with wire ties. Attach the ground clip.
9. Insert the temperature probe leads into the 12-pin connector C-6 (see illustration below). For full-
vat units or the right half of a dual-vat unit (as viewed from the rear of the fryer) the red (or
yellow) lead goes into position 3 and the white lead into position 4 of the connector. For the left
half of a dual-vat unit (as viewed from the rear of the fryer), the red (or yellow) lead goes into
position 9 and the white lead into position 10. NOTE: Right and left refer to the fryer as viewed
from the rear.
10. Secure any loose wires with wire ties, making sure there is no interference with the movement of
the springs. Rotate the elements up and down, making sure that movement is not restricted and
that the wires are not pinched.
11. Reinstall the tilt housing, back panels and contactor plug guards. Reposition the fryer under the
exhaust hood and reconnect it to the electrical power supply to return the fryer to service.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Replacing a Heating Element
1. Perform steps 1-5 of section 1.5, Replacing a Temperature Probe.
2. Disconnect the wire harness containing the probe wiring, where the temperature probe is attached
to the element being replaced. Using a pin pusher, disconnect the probe wires from the 12-pin
connector.
3. In the rear of the fryer disconnect the 6-pin connector for the left element (as viewed from the front
of the fryer) or the 9-pin connector for the right element from the contactor box. Press in on the
tabs on each side of the connector while pulling outward on the free end to extend the connector
and release the element leads (see photo below). Pull the leads out of the connector and out of the
wire sleeving.
4. Raise the element to the full up position and support the elements.
5. Remove the hex head screws and nuts that secure the element to the tube assembly and pull the
element out of the frypot. NOTE: The nuts inside the tube can be held and removed using the RE
element tube nut spanner, PN# 2304028. Full-vat elements consist of two dual-vat elements
clamped together. For full-vat units, remove the element clamps before removing the nuts and
screws that secure the element to the tube assembly.
6. If applicable, recover the probe bracket and probe from the element being replaced and install
them on the replacement element. Install the replacement element in the frypot, securing it with the
nuts and screws removed in Step 5 to the tube assembly. Ensure the gasket is between the tube and
element assembly.
7. Route the element leads through the element tube assembly and into the wire sleeving to prevent
chafing. Ensure that the wire sleeving is routed back through the Heyco bushing, keeping it clear
from the lift springs (see photos next page). Also ensure that the wire sleeving extends into the
tube assembly to protect the edge of the tube assembly from chafing the wires. Press the pins into
the connector in accordance with the diagram on the following page, and then close the connector
to lock the leads in place. NOTE: It is critical that the wires be routed through the sleeving to
prevent chafing.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Marker marks
Position 1
3
6
9
2
5
8
1
4
7
3
6
2
5
1
4
6
R
5
R
2
R
6L 5L 4L 3L 2L 1L
4R
3R
1R
Full vat element wire routing
Pull the element wires through the
bushings on either side of the frypot
and down the back. Element wires
should be routed to the right of the
ATO temperature probe on the back
wall of the frypot.
Dual vat element wire routing
Pull the element wires through the
bushings on either side of the frypot
and down the back. Element wires
should be routed to the center of the
frypot between the ATO temperature
probes.
Element grounding and wire
routing
To ground the element wires, use the
hole in the frypot frame located under
the bushing that the element wires pass
through. Using a screw through the
ground wires ring terminal, connect it
to the frypot using the probe ground
clip. Use a tie wrap to tie up half of the
element wires after the wires are pulled
through the bushing. Do not pull tie
wrap tight, leave it slack at about one
inch
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Reconnect the element connector ensuring that the latches lock.
9. Insert the temperature probe leads into the 12-pin wiring harness connector (see illustration
below). For full-vat units or the right half of a dual-vat unit, the red lead goes into position 3 and
the white into position 4. For the left half of a dual-vat unit, the red lead goes into position 9 and
the white into position 10. NOTE: Right and left refer to the fryer as viewed from the rear.
10. Reconnect the 12-pin connector of the wiring harness disconnected in Step 2.
11. Lower the element to the full down position.
12. Reinstall the tilt housing, back panels and contactor plug guard. Reposition the fryer under the
exhaust hood, and reconnect it to the electrical power supply.
1.7 Replacing Contactor Box Components
1. If replacing a contactor box component in boxes above the filter pan, first remove the filter pan
and lid from the unit. If replacing components in fryers tht have ATO boxes, the ATO box may
require removal.
2. Disconnect the fryer from the electrical power supply.
3. Remove the two screws securing the cover of the contactor box. The contactor boxes above the
filter pan are accessed by sliding under the fryer. They are located to the left and right above the
guide rails (see photo below). The contactor boxes for frypots not over the filter pan are accessed
by opening the fryer door directly under the affected frypot.
Remove two screws to access contactor box components above the filter
pan.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The contactors and relays are held on by threaded pin studs so that only removal of the nut is
required to replace the component.
5. After performing necessary service, reverse steps 1-4 to return the fryer to operation.
Left and right views of mechanical contactor box components.
Sometimes it is necessary to remove the entire contactor box to repair. Below are the instructions for
removing the far left contactor box.
1. Remove fryers from hood and remove all power to fryers.
2. Remove lower back panel.
3. Remove filter pan, lid and downspout splash shield.
4. Remove clevis clip from dispose handle at rear of fryer and let handle drop out of waste valve
bracket.
5. Remove two screws holding waste valve handle at front of fryer and remove bracket and handle
from fryer.
6. Remove AIF board and tuck wires out of the way of the contactor box for box removal.
7. Remove shipping brace that supports filter pump shelf brace to top of contactor box.
8. Remove contactor box cover.
9. Unplug all wiring from front and rear of contactor box.
10. Remove two screws that hold element wire shield to rear of contactor box and remove wire shield.
11. Remove two screws that support contactor box at rear of box.
12. Remove two screws that support contactor box at front of box.
13. Lift contactor box up to clear left frame rail and slide to the right far enough that the left rear
corner of the pump and motor shelf protrude inside of the contactor box slightly.
14. Tip front of contactor box down and to the right slightly and then pull out from opening where
filter pan lid would rest.
15. Reverse above steps for reinstallation.
1.8 Replacing a Frypot
1. Drain the frypot into the filter pan or, if replacing a frypot over the filter system, into a
McDonald’s Shortening Disposal Unit (MSDU) or other appropriate METAL container. If
replacing a frypot over the filter system, remove the filter pan and lid from the unit.
DANGER
DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.
2. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the
front and rear.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide the metal bezel up to release the bottom tabs, then slide the bezel down to disengage the
upper tabs.
4. Remove the two screws from the upper corners of the computers and allow them to swing down
(see illustration and photo on page 1-1).
5. Unplug the wiring harnesses and ground wires from the backs of the computers. Remove the
computers by lifting them from the hinge slots in the control panel frame.
6. Remove the tilt housing and back panels from the fryer. The tilt housing must be removed first in
order to remove the upper back panel.
7. To remove the tilt housing, remove the hex-head screws from the rear edge of the housing. The
housing can be lifted straight up and off the fryer.
8. Remove the control panel by removing the screw in the center and the nuts on both sides.
9. Loosen the component boxes by removing the screws, which secure them in the cabinet.
10. Dismount the top cap by removing the nuts at each end that secure it to the cabinetry.
11. Remove the hex head screw that secures the front of the frypot to the cabinet cross brace.
12. Remove the top-connecting strip that covers the joint with the adjacent frypot.
13. Unscrew the nut located on the front of each section of drain tube, and remove the tube assembly
from the fryer.
14. Remove the actuators from the drain and return valves and disconnect the wiring.
15. Disconnect any auto filtration probes and auto top off sensors and wiring.
16. At the rear of the fryer, unplug the 12-pin connector C-6 and, using a pin pusher, disconnect the
high-limit thermostat leads. Disconnect any other probe wiring.
17. Disconnect the oil return flexline(s).
18. Raise the elements to the “up” position and disconnect the element springs.
19. Remove the machine screws and nuts that secure the element tube assembly to the frypot.
Carefully lift the element assembly from the frypot and secure it to the cross brace on the rear of
the fryer with wire ties or tape.
20. Carefully lift the frypot from the fryer and place it upside down on a stable work surface.
21. Recover the drain valve(s), oil return flexline connection fitting(s), actuators, AIF boards and high-
limit thermostat(s) from the frypot. Clean the threads and apply Loctite™ PST 567 or equivalent
sealant to the threads of the recovered parts and install them in the replacement frypot.
22. Carefully lower the replacement frypot into the fryer. Reinstall the hex head screw removed in
step 11 to attach the frypot to the fryer.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
23. Position the element tube assembly in the frypot and reinstall the machine screws and nuts
removed in step 19.
24. Reconnect the oil return flexlines to the frypot, and replace aluminum tape, if necessary, to secure
heater strips to the flexlines.
25. Insert the high-limit thermostat leads disconnected in step 16 (see illustration on page 1-3 for pin
positions).
26. Reconnect the actuators, ensuring the correct position of the drain and return valves.
27. Reconnect the auto filtration and auto top off probes.
28. Reinstall the drain tube assembly.
29. Reinstall the top connecting strips, top cap, tilt housing and back panels.
30. Reinstall computers in the control panel frame and reconnect the wiring harnesses and ground
wires.
31. Reposition the fryer under the exhaust hood and reconnect it to the electrical power supply.
1.9 Built-in Filtration System Service Procedures
1.9.1 Filtration System Problem Resolution
One of the most common causes of filtration problems is placing the filter pad/paper on the bottom of
the filter pan rather than over the filter screen.
CAUTION
Ensure that filter screen is in place prior to filter pad/paper placement and filter pump
operation. Improper screen placement is the primary cause of filtration system
malfunction.
Whenever the complaint is “the pump is running, but no oil is being filtered,” check the installation of
the filter pad/paper, and ensure that the correct size is being used. While you are checking the filter
pad/paper, verify that the O-rings on the pick-up tube of the filter pan are in good condition. A
missing or worn O-ring allows the pump to take in air and decrease its efficiency.
If the pump motor overheats, the thermal overload will trip and the motor will not start until it is reset.
If the pump motor does not start, press the red reset switch (button) located on the rear of the motor.
If the pump starts after resetting the thermal overload switch, then something is causing the motor to
overheat. A major cause of overheating is when several frypots are filtered sequentially, overheating
the pump and motor. Allow the pump motor to cool at least 30 minutes before resuming operation.
Pump overheating can be caused by:
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Sediment Particle
• Solidified shortening in the pan or filter
lines, or
• Attempting to filter unheated oil or
shortening (cold oil is more viscous,
overloading the pump motor and causing
it to overheat).
Oil Flow
If the motor runs but the pump does not return
oil, there is a blockage in the pump. Incorrectly
sized or installed paper/pads will allow food
particles and sediment to pass through the filter
pan and into the pump. When sediment enters
the pump, the gears bind, causing the motor to
overload, again tripping the thermal overload.
Shortening that has solidified in the pump will
also cause it to seize, with the same result.
Sediment Particle
Up for reverse
Down for forward
A pump seized by debris or hard shortening can
usually be freed by manually moving the gears
with a screwdriver or other instrument.
Disconnect power to the filter system, remove the input plumbing from the pump, and use a
screwdriver to manually turn the gears.
● Turning the pump gears in reverse will release a hard particle.
● Turning the pump gears forward will push softer objects and solid shortening through the pump
and allow free movement of the gears.
Incorrectly sized or installed paper/pads will also allow food particles and sediment to pass through
and clog the suction tube on the bottom of the filter pan. Particles large enough to block the suction
tube may indicate that the crumb tray is not being used. Pan blockage can also occur if shortening is
left in the pan and allowed to solidify. Blockage removal can be accomplished by forcing the item out
with an auger or drain snake. Compressed air or other pressurized gases should not be used to force
out the blockage.
1.9.2 Replacing the Filter Motor, Filter Pump, and Related Components
1. Remove the filter pan and lid from the unit. Drain the frypots into a McDonald’s Shortening
Disposal Unit (MSDU) or other appropriate metal container.
DANGER
DO NOT drain more than one full frypot or two split frypots into the MSDU at one time.
2. Disconnect the fryer from the electrical power supply and reposition it to gain access to both the
front and rear.
3. Disconnect the flexline running to the oil-return manifold at the rear of the fryer as well as the
pump suction flexline at the end of the filter pan connection (see photo on the following page).
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnect flexlines indicated by the arrows.
4. Loosen the nut and bolt which secure the bridge to the oil-return manifold.
5. Remove the cover plate from the front of the motor and disconnect the motor wires.
6. Remove the two nuts and bolts which secure the front of the bridge to the cross brace and carefully
slide the bridge rearward off the cross brace until its front end can be lowered to the floor. Undo
the single nut holding it in place in back. Be careful not to let the rear of the bridge slip off the
manifold at this point.
7. Get a good grip on the bridge, carefully pull it forward off the oil-return manifold, and lower the
entire assembly to the floor. Once on the floor, pull the assembly out the front of the fryer.
8. When required service has been completed, reverse steps 4-7 to reinstall the bridge.
9. Reconnect the unit to the electrical power supply, and verify that the pump is functioning correctly
using the MIB board in manual mode (i.e., using the fill function when engaged, the motor should
start and there should be strong suction at the intake fitting and outflow at the rear flush port.)
10. When proper operation has been verified, reinstall the back panels and the filter pan and lid.
11. Reconnect it to the electrical power supply and reposition the fryer under the exhaust hood to
return the fryer to service.
1.9.3 Replacing the Transformer or Filter Relay
Disconnect the fryer from the electrical power supply. Remove the left computer from the fryer to
expose the interior of the left component box. The transformer and relay on the left are located as
shown in the illustration on the next page. NOTE: The right component box is identical to the left
except that the transformer and relay on the left side are not present. Once replaced, reconnect the
power.
When replacing a filter relay in the left component box, ensure the 24VDC relay (8074482) is used.
Similar Frymaster fryers use a 24VAC relay, which can lead to confusion. The 24VDC is used in the
LOV™ fryer.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
1.10 ATO (Automatic Top-off) Service Procedures
The automatic top-off system is activated when the oil level falls below a sensor in the rear of the frypot.
The signal is sent to the ATO board to engage the return actuator to the frypot and turn on the ATO pump.
The pump draws oil from the JIB (Jug In Box) through the rear return manifold into the rear of the frypot.
Once the oil level has satisfied the sensor, the pump turns off and the actuator closes.
The ATO board is located inside the box, behind the JIB (see Figure 1).
The power for the ATO board is supplied from the right hand component
box. The power passes through the transformer inside the ATO box to the
board.
Figure 1
1.10.1 ATO (Automatic Top-off) Troubleshooting
Problem
Probable Causes
Corrective Action
Ensure setpoint is correct.
Frypot tops off cold. Incorrect setpoint
A. Check to ensure J5 on front of ATO
board is fully locked into connector.
A. J5 connection unplugged
B. Fuse blown
C. Transformer malfunction
B. Ensure fuse below right control box is
not blown and fuse on the right side of
ATO box is not blown.
C. Check that proper voltage is present at
transformer. See table in section 1.10.2.
No power to ATO board
A. Loose wire connection
A. Ensure the yellow LED is securely
attached to plug J6 on the ATO board.
B. Power in the component box is not
present.
B. Ensure power is present in the
component box.
C. If power is present in component box,
check the transformer for correct
voltage.
The yellow JIB low light
won’t illuminate.
C. Failed transformer.
A. Loose wire connection.
B. Actuator issue
A. Ensure all wiring harnesses are securely
connected to ATO board and solenoids.
B. Check return actuator to ensure actuator
is functional.
One vat tops off but
other vats fail to top off.
A. Wired incorrectly.
B. Flexlines connected to wrong vat.
A. Check wiring.
B. Switch flexlines to correct vat.
Incorrect vat tops off.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Probable Causes
Corrective Action
A. Ensure JIB has oil.
B. Check to see that fryer is heating.
Fryer temperature must be at setpoint.
Check probe resistance. If probe is
bad, replace the probe.
C. Ensure that the oil in the JIB is above
70°F (21°C).
A. Empty JIB.
D. With the computer OFF, press TEMP
button and ensure the ATO software
version appears. If not, the connection
between the AIF and the ATO board
may be bad. Ensure the 6-pin CAN
connectors are tight between AIF (J4
and J5) and ATO (J10) boards.
E. Power to the ATO board has been cut
off. Restore power to the board and
clear any service required errors.
F. Ensure transformer in ATO box is
functioning properly. Check power
from transformer to ATO board.
Ensure all harnesses are plugged
securely into place.
B. Probe temperature lower than setpoint.
C. Oil is too cold.
D. Bad Connection
E. ATO board power loss
F. Failed transformer/harness
G. ATO pump failed
Frypots won’t top off.
H. Failed ATO board.
I. ATO lines/pump plugged
G. Ensure pump is operational. Check
voltage to pump. Replace the pump if
defective.
H. Check for proper voltages using the pin
position chart found on page 1-15. If
ATO found defective, replace ATO
board and clear any errors.
I. Clear the lines/pump.
A. Clear filter error properly.
When
change filter pad YES/NO is displayed,
do NOT press any button until the pan
has been removed for at least thirty
seconds. After thirty seconds have
elapsed, the computer returns to OFF or
last display.
A. Filter error exists.
One vat doesn’t top off.
B. Actuator, pump, loose connection, RTD
or ATO issue.
B. Check actuator, ATO pump, wire
connections, RTD and ATO board.
A. Ensure fuse on right side of ATO box is
secure and good. If the computer
above the ATO box is missing power
check the fuse below the component
box.
B. With the computer OFF, press TEMP
button and ensure the ATO software
version appears. If not, the connection
between the AIF and the ATO board
may be bad. Ensure the 6-pin CAN
connectors are tight between AIF (J4
and J5) and ATO (J9 or J10) boards.
M3000 displays
SERVICE
REQUIRED – ATO
BOARD
A. Loose or bad fuse
B. Bad Connection
C. ATO Board power loss
C. Power to the ATO board has been cut
off. Ensure there is correct voltage to
the ATO transformer. Restore power to
the board and clear any service required
errors.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
1.10.2 ATO (Automatic Top-Off) Board Pin Positions and Harnesses
Pin
Wire
Connector
From/To
RTI Add Solenoid
Harness #
#
Function
24VAC Ret
Voltage
24VAC
Color
Black
1
2
3
ATO Pump Relay
24VAC
Black
4
24VAC Ret
5
6
7
JIB Reset Switch
RTI Add Solenoid
16VDC
24VAC
8
JIB Low Reset
24VAC
Black
Red
J8
8074671
9
10
11
ATO Pump Relay
24VAC
Red
12 24VAC
13
14
15
JIB Reset Switch
Transformer
16VDC
24VAC
16 Ground
Red
Orange
Blue
1
2
3
4
5
6
7
8
1
2
3
4
24VAC Ret
24VAC
8074553
8074657
J4 (Rear) /
J5 (Front)
12VAC Ret
12VAC
Red
Brown
Black
Black
White
Red
12VAC
Ohm
Jumper
ATO 4 & 5 Battery
Jumper
Jumper
DV - Probe Ground
DV - Probe
FV - Probe Ground
FV - Probe
J3 - Vat #3
J2 - Vat #2
J1 - Vat #1
8074655 - Vat #1
8074654 - Vat #2
8074621 - Vat #3
ATO RTD
Ohm
White
Red
1
2
1
2
3
4
5
1
2
3
4
5
6
1
2
3
4
5
6
16VDC
Black
Red
J6
J7
Orange LED
8074555
16VDC
16VDC Ret
Ground
RB7/DATA
RB6/CLOCK
Ground
CAN Lo
CAN Hi
5VDC+
Black
Red
Network Resistor
(pins 2 & 3)
or to next ATO Board (4
& 5 vat units)
White
Black
Red
J10
8074552
5VDC
24VDC
24VDC
Ground
Ground
CAN Lo
CAN Hi
5VDC+
White
Black
Red
White
Black
Red
J9
AIF J5
8074546
5VDC
24VDC
24VDC
Ground
White
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
1.10.3 Replacing the ATO board, LON Gateway, ATO pump relay or Transformers
Disconnect the fryer from the electrical power
supply. Locate the ATO box (see Figure 1 on page
12), behind the JIB (Jug In Box). Remove the cover
to expose the transformers, relay and LON gateway
(if installed) (see Figure 2). Mark and unplug any
wires or harnesses. Once the LON gateway is
removed the ATO board is visible (see Figure 3).
Replace the defective component and reattach all
wires or harnesses.
Replace the cover. Once
replaced, CYCLE POWER TO ENTIRE FRYER
SYSTEM. See section 1.11.7 on page 1-22 to reset
control power. Check software version and if
necessary update the software. If a software update
was necessary, follow the instructions to update the
software in section 1.15
Figure 2
Figure 3
Press the TEMP button on one of the M3000 computers, with the computer in the OFF position, to verify
software version of the ATO. If the version is not visible, the ATO may not be connected properly.
1.10.4 Replacing the ATO Pump
Disconnect the fryer from the electrical power
supply. Locate the ATO pump (see Figure 4), behind
the ATO box. Mark and unplug any wires or
harnesses. Press up from the bottom on the quick
disconnects to release the plumbing (see Figure 5).
The plumbing can be pulled from the pump. Loosen
the four nuts attaching the pump to the pump tray.
Replace the defective component and reverse above
steps. Once replaced, reconnect the power.
Figure 4
Figure 5
1.11 MIB (Manual Interface Board) Service Procedures
The MIB (Manual Interface Board) oversees and controls filtration. It receives and sends data over the CAN
(Controller Area Network) to and from various sensors and computers. It activates the filtration cycle,
controlling when actuators should open and close.
The MIB controller is located inside the left cabinet (see Figure 6). In normal operation a cover hides the MIB
controls and only the LED display is visible. The cover is held in place with three torx screws. In normal
operation, an “A” is displayed for automatic mode. The MIB control board is useful for diagnostic purposes. It
allows manual operation of both the actuators and filter pump without using the M3000 computer.
Mode Display
Reset Switch
Drain Switch
Vat Selector
Switch
Manual /Auto
Switch
Return Switch
Figure 6: MIB controller cover.
Figure 7
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Buttons and LED’s
Manual – This button is used to toggle between auto and manual filtration mode. A corresponding
LED is lit when in Manual mode. When pressed, a message will be sent to all vats, indicating the
mode has changed.
The following buttons are inoperable in auto mode:
Select - This button is used to scroll through available vats, choosing one to be manually filtered.
Drain – This button is used to open and close the drain on the vat indicated on the display. It’s
embedded LED indicates the following activity:
Blink: Actuator is moving or awaiting a response from the AIF board.
Constant Illumination: Drain open.
No Illumination: Drain closed.
Return – This button is used to open and close the return valve on the vat indicated on the display.
When pressed and held, it also turns on and off the pump. It’s embedded LED indicates the following
activity:
Blink: Actuator is moving or awaiting a response from the AIF board.
Constant Illumination: Return valve open.
No Illumination: Return valve closed.
1.11.1 Manually Draining, Refilling or Filtering using the MIB board
Press the manual/auto switch to set to manual.
The LED on the manual key will illuminate and
a vat number is displayed (see Figure 8).
Figure 8
Press the vat selector switch to change vats (see
Figure 9).
Figure 9
Pressing the drain or the return switch
illuminates and activates the drain or return
valve for the vat indicated. Pressing and holding
the return switch while the return is open
activates the filter motor and pump (see Figure
10).
Figure 10
Pressing the manual/auto switch will return to
automatic mode.
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
1.11.2 MIB (Manual Interface Board) Troubleshooting
Problem
Probable Causes
Corrective Action
A. Ensure filter pan is fully inserted into fryer.
If the MIB board displays a “P” the pan is
not fully engaged into the pan switch.
B. Ensure the oil level is above the top oil
level sensor.
C. Ensure MIB board is in “A” automatic
mode.
D. Remove and replace cover and see if
filtration will start.
E. Replace filter relay with part number 807-
4482 24VDC relay.
F. Set AIF disable in Level 1 to NO.
G. Press filter motor thermal switch.
H. Ensure AIF clock is set to disabled.
A. Filter pan out of position.
B. Oil level too low.
C. Ensure MIB board is not in
manual mode.
D. Ensure MIB cover is not
damaged and pressing against
buttons.
E. Filter relay has failed.
F. AIF disable is set to YES, blue
light doesn’t light.
G. Filter motor thermal switch is
tripped.
Auto filtration won’t
start.
H. AIF clock enabled
MIB display shows
something other than
an “A” or vat number.
An error has occurred and
displayed character indicates
error.
See MIB display diagnostics on page 1-21 for
explanation.
Check output on the left transformer in left
component box; should read 24VAC. If not
replace transformer.
No power present at Transformer has failed in left
the MIB board component box.
Press and hold reset button in top right corner
of MIB board for five seconds. The drain,
return and manual/auto LEDS will illuminate
and the MIB will reset and clear any remaining
errors from memory. Allow 60 seconds to reset.
If an error still exists, then another issue exists.
A. Ensure the CAN bus system is terminated at
BOTH ENDS (on the M3000 connector J6
and on the ATO board connector J9) with a
resistor equipped 6-pin connector.
MIB will not clear Error remains in non-volatile
error. memory.
B. Unplug and reseat all wiring harnesses in
CAN system. Resistance between pins 2
and 3 on the CAN network connectors
should be 120 ohms.
A. Network is not terminated
correctly.
MIB indicates
C. Check software version numbers on all
M3000 computers and ensure all are display
an AIF version. If an AIF version is
missing, the AIF board may be missing
power or bad. Check pins 5 and on J4 and
J5 of the affected AIF board for proper
voltage.
B. Wiring harnesses are loose or
incorrect number of
damaged.
vats.
C. An AIF board issue.
D. Locator pin issue.
D. The locator pin in J2 of the AIF board is
either loose or in the incorrect position. See
the charts on page 1-55 of this manual for
proper pin position.
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Probable Causes
Corrective Action
A. Ensure the CAN bus system is terminated at
BOTH ENDS (on the M3000 connector J6
and on the ATO board connector J10) with a
resistor equipped 6-pin connector.
B. With the computer OFF, press TEMP button
and ensure the AIF version appears. If not,
the 24V to the AIF boards may be missing.
Ensure all 6-pin CAN connectors are tight
between the M3000 (J6 and J7), MIB (J1
and J2), AIF (J4 and J5) and ATO (J10)
boards.
C. With the computer OFF, press TEMP button
and ensure the ATO version appears. If not,
check the CAN wire harness between the
AIF board J4 or J5 and the ATO board J9 or
J10. The ATO fuse on the right side of the
ATO box may be loose or blown; the 110V
to the ATO transformer may be missing or
the transformer bad. The J4/J5 connector
may be loose. Is the right computer
functioning? If not the fuse below the
contactor box may be loose or blown.
D. Check to see if MIB has 24V on pins 5 and
6 of J2. Check to see if 24V is present on
pins 5 and 6 of wire harness plugging into J4
or J5 of the first AIF board. If 24V missing,
check the pins. Replace the harness if
necessary.
MIB board alternating
“E” and “vat number
and side”.
Network error on the CAN bus
communication.
E. Check continuity between each color wire
on the CAN connectors into J7 on the far
right computer and J10 on back of the ATO
board (black to black, white to white, and
red to red), and ensure there is no continuity
between different color wires (black to red,
red to white, and white to black).
F. Ensure black computer locator wires are
connected from ground to correct pin
position (see drawing 8051734 page 1-55).
G. Ensure all boards have the corner ground
wire attached and tightened.
H. The locator pin in J2 of the AIF board is
either loose or in the incorrect position. See
the charts on page 1-55 of this manual for
proper pin position.
I. Bad MIB and/or AIF board.
J. Broken resistor lead. Unwrap the resistor
leads and check ends.
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
1.11.3 MIB (Manual Interface Board) Pin Positions and Harnesses
Connector
From/To
Harness # Pin #
Function
Voltage
Wire Color
Black
1
2
Ground
CAN Lo
CAN Hi
Red
3
White
J1
M3000 J7
8074546
4
5
6
1
2
Ground
CAN Lo
CAN Hi
5VDC+
24VDC
Ground
24VAC
Black
Red
3
White
Black
Red
J2
AIF J4
8074547
4
5VDC
5
6
1
2
3
4
5
6
24VDC
White
Black
White
Red
Transformer
Filter Relay
Blue LED
24VAC
24VDC
24VDC
24VAC Ret
Pump Motor
Pump Motor
Blue LED +
Green
Red
Blue LED -
Black
Black
Red
8074649
RTI Open Switch
RTI Closed Switch
7
Open Switch +
Closed Switch +
RTI
8
J5
9
8074844
NON-RTI
10
11 Pan Sw +
12 Pan Sw -
13
Black
Red
Pan Switch
24VDC
14
RTI Open Switch
RTI Closed Switch
15 Ground -
16 Ground -
White
Green
Black
White
Green
1
2
3
4
5
6
7
From RTI transformer
24VAC
24VAC
Common
To RTI "Add Pump" Relay
To RTI connection in
rear of fryer
J6
8074760
24VAC –
Full
0VAC –
Not Full
From RTI "Waste Tank Full
Sensor" Test Pins 2 to 8
8
Red
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
1.11.4 MIB (Manual Interface Board) Display Diagnostics
DISPLAY
LED
EXPLANATION
Drain valve on vat # is open
Drain
Vat # (The vat number is followed by On
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
Vat # (The vat number is followed by Off
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
Drain valve on vat # is closed
Vat # (The vat number is followed by Blink
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
Drain valve on vat # is opening or closing or an
error condition may exist.
Return
Vat # (The vat number is followed by On
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
Vat # (The vat number is followed by Off
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
Return valve on vat # is open
Return valve on vat # is closed
Vat # (The vat number is followed by Blink
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
Return valve on vat # is opening or closing or an
error condition may exist
Network
N
Network error, displays for 10 seconds if no
communications are received from the M3000
within 10 seconds after power on or MIB reset.
Resetting
r
An “r” is displayed for ten seconds or until
communication is received from the M3000 after a
power on or MIB reset.
Miscellaneous
E alternating with vat # (The vat Blink
number is followed by an “L” to
indicate left side of a split vat or an
“r” to indicate the right side of a split
vat or a full vat.)
The circuit has an issue. Ensure the actuator is
plugged in. Ensure the CAN connections are all
securely plugged into the connectors.
Indicates the AIF temperature sensor did not detect
a full vat during filtration.
A
Manual LED off
The system is in auto filtration mode.
The system is in manual mode.
Vat # (The vat number is followed by Manual LED on
an “L” to indicate left side of a split
vat or an “r” to indicate the right side
of a split vat or a full vat.)
P
This will only be displayed in auto filtration mode.
Filter pan is improperly seated. Any auto filtration
messages received at this time are ignored.
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
1.11.5 MIB (Manual Interface Board) Display Characters
A – Auto Mode – Auto Filtration enabled.
E – Drain or return valve is not in desired state. The display will alternate between E and the corresponding vat
number. Ensure the actuator is plugged in and an error does not exist.
– Three horizontal lines indicate the AIF temperature sensor did not detect that the vat was full during
auto filtration.
n – Network Error - An “n” displays for 10 seconds if no communication is received from the cooking
computer within ten seconds after a power on or MIB reset.
P – Pan Switch – Filter pan is improperly seated. Filtration is suspended.
r – Reset Switch - Reset the vat closes all of the valves on the vat. If displayed for some time, there is probably
a problem with the board.
1 – 5 – Numbers which correspond to the vats with either an “L” indicating the left side of a split vat or “r”
indicating the right side of a split vat or a full vat. These numbers are displayed in manual mode.
1.11.6 Replacing the MIB Board
Disconnect the fryer from the electrical power supply. Remove the torx screws from the MIB cover, exposing
the MIB board (see Figure 11). Removing the screw at top center lets the MIB board hinge down. Carefully
remove the plugs on the rear of the board (see Figure 12). Replace with a new MIB board and reverse steps to
reassemble. Once replaced, CYCLE POWER TO ENTIRE FRYER SYSTEM. See next section to reset
control power. Check software version # and if necessary update the software. If a software update was
necessary, follow the instructions to update the software on in section 1.15 ensuring the MIB reset button is
pressed and held for five seconds at the end of the update to update the MIB.
Figure 11
Figure 12
1.11.7 Control Power Reset Switch
The control power reset switch is a momentary
rocker switch located behind the control box
(see Figures 13 and 14) above the JIB that
resets all power to all the computers and boards
in the fryer. It is necessary to reset all power
after replacing any computer or board. Press
and hold the switch for at least ten seconds
when resetting the control power to ensure
power has sufficiently drained from boards.
Figure 13
Figure 14 (Rear view of Control Box)
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
1.12
RTI Service Issues
1.12.1 RTI MIB Tests
The LOV™ fryer will ONLY operate with RTI systems that have the new RTI updated
three-pole float switch. If the float switch is the older two-pole switch, call RTI. These
float switches are polarity specific which may short to ground and damage an MIB
board.
Normal measurements (MIB J6 8-pin connector with everything connected)
AC voltage measurements:
Pin 1 to Pin 2 - 24 VAC.
Pin 2 to Pin 8 - 24 VAC when waste tank is full, 0 VAC when it is not full.
Pin 2 to Pin 3 - 24 VAC when RTI fill pump is on, 0 VAC when it is off.
Using the RTI test box, PN# 108-0716 allows a quick and easy way to check the 24VAC, the waste
full switch and when the RTI pump is operating.
Troubleshooting
All return and drain valves should be closed and pump should be off while the MIB is resetting. If any
of the valves or the pump is on during reset, the MIB board is bad or wires are shorted.
RTI pump is not operating or JIB is not filling:
See page 1-26 to ensure that no other function is taking priority over adding oil to jug.
1. Reset the power; wait 60 seconds and see if the valve opens.
With the JIB button pressed:
2. Voltage at MIB board from Pin 1 to Pin 2 should be 24 VAC; if not, check connections from RTI
24VAC transformer and check transformer.
3. Voltage at MIB board from Pin 1 to Pin 3 should be 24 VAC when filling JIB or vat; if not, the MIB
board is bad or wires to pump relay are shorted or both.
4. Voltage at Add pump relay should be 24 VAC; if not, check wiring from MIB board. The relay is
located on top of RTI system.
5. Check voltage at ATO board on J8. Pin 9 to Pin 1 should be 24 VAC with the orange button
pressed.
Waste full signal:
Pin 2 to Pin 8 should be 24 VAC when full, 0 VAC when not full; if no voltage level change, the
connection from RTI switch or MIB board is bad.
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
1.12.2 RTI LOV™ Wiring
1.12.3 Frymaster LOV™ Fryer and RTI Bulk Oil System Plumbing Schematic
1-24
Download from Www.Somanuals.com. All Manuals Search And Download.
1.12.4 RTI LOV™ TEST QUICK REFERENCE
DISPOSE TO WASTE, REFILL VAT FROM BULK:
1. Hold down “Filter” button until computer beeps twice.
2. Scroll down to “Dispose” using “Info" button then press “9” button.
3. “Dispose? Yes/No” is displayed.*
4. Press “9” to dispose of oil in pot.
5. “Draining” is displayed.
6. “Vat Empty? Yes” is displayed.
7. Press “9”.
8. “Cln Vat Complete? Yes” is displayed.
9. Press “9”.
10. “Open Dispose Valve” is displayed. Open dispose valve.
11. “Disposing” is displayed for five minutes.
12. “Remove Pan” is displayed. Remove pan.
13. “Is Pan Empty? Yes No” is displayed.
14. Press “9” if filter pan is empty. Select “8” if pan still has oil in it.
15. “Close Dispose Valve” is displayed. Close dispose valve.
16. “Insert Pan” is displayed. Insert pan.
17. “Fill Vat From Bulk? Yes/No” is displayed.
18. Press “9”.
19. “Press and Hold Yes to Fill” alternating with “Yes” is displayed.
20. Hold down “9” to fill pot to desired level.
21. “Filling” is displayed while button is depressed.
22. “Continue Filling Yes/No” is displayed
23. Press “9” to continue filling or “8” to Exit program.
*NOTE: If the waste tank is full, the computer displays “RTI Tank Full.” Call RTI.
DISPOSE TO WASTE:
1. Hold down “Filter” button until computer beeps twice.
2. Scroll down to “dispose” using “Info” button and press “9” button.
3. “Dispose? Yes/No is displayed.
4. Press “9”.
5. “Draining” is displayed.
6. “Vat Empty? Yes is displayed.
7. Press “9”
8. “Cln Vat Complete? Yes” is displayed.
9. Press “9”.
10. “Open Dispose Valve” is displayed.
11. Open dispose valve by pulling completely forward to start disposal.
12. “Disposing” is displayed for four minutes.
13. “Remove Pan” is displayed.
14. Slide the filter pan slightly out of the fryer.
15. “Is Pan Empty? Yes/No” is displayed.
16. Press “9” if the filter pan is empty. Select “8” if pan still has oil in it.
17. “Close Dispose Valve” is displayed.
18. Close the dispose valve ensuring the handle is pushed completely towards the fryer.
19. “Insert Pan” is displayed.
20. “Fill Vat From Bulk? Yes/No” is displayed.
21. Press “8” if you wish to leave pot empty and exit.
FILL VAT FROM BULK:
1. Hold down “filter” button until computer beeps twice.
2. Scroll down to “Fill Vat from Bulk” using the Info button.
3. Press “9”.
4. “Fill Vat from Bulk? Yes/No” is displayed.
5. Press “9”.
6. “Press and Hold Yes to Fill / Yes” is displayed.
7. Press and hold down “9” to fill pot to desired level.
1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
8. “Filling” is displayed during fill.
9. Release button to stop filling.
10. “Continue Filling? Yes/No” is displayed.
11. Press “8” to exit.
FILL JUG FROM BULK:*
1. When “Orange” indicator light is on, the top-off jug is empty.
2. To refill jug press and hold the orange reset button above the jug until the jug is full.
3. Release the button to stop filling.
*NOTE: The jug may not fill if any of the following are in progress:
If FILTER NOW? YES/NO, CONFIRM YES/NO, or SKIM VAT is displayed, the fill jug button is disabled until either a
filter is complete or until no is chosen.
The system also checks these conditions. The following must be met before jug fill is allowed.
Solenoid closed
•
•
•
•
Orange fill button pressed longer than 3 sec.
Waste valve closed
Filter Now? Yes/No, Confirm Yes/No, or Skim Vat cannot be displayed
System power cycle (all boards – computers, MIB, AIF and ATO) after changing setup from JIB to Bulk (use
momentary reset). Ensure reset is pressed and held for at least ten seconds.
•
No filtration or other filter menu selection can be in process.
Other factors that may not allow fill jug from bulk –
•
•
•
•
Defective solenoid
Defective switch
RTI pump issue
RTI relay stuck
If using two fryer systems that are both attached to the RTI system, they may not be able to fill both units at the same
time if they have an RTI unit with a single head. Some RTI units have dual heads which can fill simultaneously.
1-26
Download from Www.Somanuals.com. All Manuals Search And Download.
1.13 AIF (Automatic Intermittent) Filtration Service Procedures
The AIF (Automatic Intermittent Filtration) board controls the
actuators that open and close the drain and return valve. The
AIF boards are located inside a protective housing under each
frypot (see Figure 13).
Figure 13
1.13.1 AIF Troubleshooting
Problem
Probable Causes
Corrective Action
A. Check pins 5 and 6 of J2 at the MIB
board. Should read 24VDC. Check
voltage on pins 5 and 6 at the other
end of harness and ensure 24VDC is
present. Continue to check pins 5 and
6 for 24VDC on plugs J4 and J5 on the
AIF boards.
B. Ensure the actuator is plugged into the
proper connection (J1 for FV return, J3
for DV return and J6 for FV drain and
J7 for DV drain).
C. Check power on the connector of the
problem actuator while trying to
manually open or close an actuator.
Pins 1 (Black) and 4 (White) should
read +24VDC when the actuator is
opening. Pins 2 (Red) and 4 (White)
should measure -24VDC when the
actuator is closing). If either voltage is
missing, the AIF board is likely bad.
Test the actuator by plugging into
another connector. If the actuator
operates, replace the board.
A. No power to the AIF board.
B. Actuator is unplugged.
C. AIF board failure.
Actuator doesn’t
function.
D. Actuator readings are out of tolerance.
E. Actuator is bad
D. Check resistance of the potentiometer
between pin 3 (purple wire) and pin 4
(gray/white wire). Closed should read
0-560Ω. Open should read 3.8K Ω –
6.6K Ω.
E. If proper voltages are present at the
connector and actuator doesn’t
operate, reset power to the fryer. If it
still doesn’t operate replace the
actuator.
A. Ensure the actuator is plugged into
correct connection (J1 for FV return,
J3 for DV return and J6 for FV drain
and J7 for DV drain).
B. Ensure the locator pin is in proper
position in plug J2. See table B on
page 1-55.
A. Actuator plugged into wrong connector.
B. Locator pin is in wrong position.
Actuator functions on
wrong vat.
1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
1.13.2 AIF (Auto Intermittent Filtration) Actuator Board Pin Positions and Harnesses
Pin
#
1
2
Wire
Color
Black
Red
Connector
J1
From/To
Harness PN
N/A
Function
Ret + (Open)
Voltage
24VDC
24VDC
Ret – (Closed)
Ret Position
Ground
FV Return
Actuator
3
Purple
White
White
Red
4
1
Ground
FV AIF RTD
DV AIF RTD
2
FV - Temp
Ground
3
White
Red
4
DV - Temp
5
6
7
8
J2
DV – OLS (Gas)
FV – OLS (Gas)
Locator Vat #5
Locator Vat #4
Locator Vat #3
Locator Vat #2
Locator Vat #1
Locator Signal
Ret + (Open)
Ret – (Closed)
Ret Position
Ground
9
Oil Level Sensor
(Gas)
10
11
12
13
14
15
16
1
Locator Pin
Locator
Black
Black
Black
Red
24VDC
24VDC
2
DV Return
Actuator
J3
J4
N/A
3
Purple
White
Black
Red
4
1
Ground
2
CAN Lo
8074547
AIF Board
Communication
and Power
3
CAN Hi
White
Black
Red
MIB J2 or
AIF J5
4
5VDC+
5VDC
5
24VDC
24VDC
6
Ground
White
Black
Red
1
Ground
2
CAN Lo
8074547
AIF Board
Communication
and Power
3
CAN Hi
White
Black
Red
AIF J4 or
ATO J10
J5
4
5VDC+
5VDC
5
24VDC
24VDC
6
Ground
White
Black
Red
1
Drain + (Open)
Drain – (Closed)
Drain Position
Ground
24VDC
24VDC
2
FV Drain
Actuator
J6
J7
N/A
N/A
3
Purple
White
Black
Red
4
1
Drain + (Open)
Drain – (Closed)
Drain Position
Ground
24VDC
24VDC
2
DV Drain
Actuator
3
Purple
White
4
1-28
Download from Www.Somanuals.com. All Manuals Search And Download.
1.13.3 Replacing an AIF (Automatic Intermittent Filtration) board
Disconnect the fryer from the electrical power supply. Locate the AIF board to be replaced under a frypot.
Mark and unplug the harnesses. The AIF board assembly is held in place with one screw in the front of the
assembly (see Figure 14). Remove the screw and the front of the assembly drops down (see Figure 15) and
the back tab slides out of the bracket attached to the frypot (see Figure 16). Reverse steps to reassemble,
ensuring that the new AIF assembly slides into the slot in the rear of the bracket. Once complete, CYCLE
POWER TO ENTIRE FRYER SYSTEM. See section 1.11.7 on page 1-22 to reset control power. Check
software version # and if necessary update the software. If a software update was necessary, follow the
instructions to update the software in section 1.15.
Figure 14
Figure 15
Figure 16
1.13.4 Replacing a Linear Actuator
Disconnect the fryer from the electrical power supply. Locate the actuator to be replaced under a frypot
and mark and unplug the actuator. The actuators are held in place by two clevis pins which are held in by
“J” clips (see Figure 17). Twist and remove both “J” clips and clevis pins (see Figure 18). It may be
necessary to remove the AIF board to access the pins. Remove the actuator and attach the new actuator
with only the rear clevis pin and “J” clip. Align the alignment holes and insert the clevis pin into both
holes (see Figure 19). Rotate the actuator shaft until the holes of the shaft and valve plate align (see Figure
20). Remove the pin from the alignment hole and insert into the actuator shaft and valve handle (see
Figure 21). Insert the “J” pin to secure (see Figure 22).
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
1.13.5 Replacing a Rotary Actuator
Disconnect the fryer from the electrical power supply. Locate the actuator to be replaced and mark and
unplug the actuator. The actuators are held in place by two allen screws. Loosen the allen screws. It may
be necessary to remove a gas line to the burner when removing a drain actuator. Remove the actuator from
the valve stem. Align the actuator with the valve stem and attach the new actuator. Tighten the two allen
screws. Reconnect power and test the actuator.
NOTE: Rotary actuators have two different part numbers, which are mirror images of each other that
correspond to their mounting position.
1.14
M3000 Computer Service Procedures
1.14.1 M3000 Computer Troubleshooting
Problem
Probable Causes
Corrective Action
A. Press the ON/OFF switch to turn the
computer on.
B. This fryer may have two cords: a
computer power cord and a main power
cord. If the computer cord is not plugged
in, the computer will not activate. Verify
computer power cord is plugged in and
that circuit breaker is not tripped.
C. Some fryers have a rocker power switch
inside the cabinet below the computer.
Ensure the switch is turned on.
A. Computer not turned on.
B. No power to the fryer.
C. Power switch turned off.
D. Loose fuse holder.
No Display on
D. Ensure fuse holder is screwed in properly.
E. Swap the computer with a computer
known to be good. If computer functions,
replace the computer.
E. Computer has failed.
Computer.
F. Damaged computer wiring harness.
G. Power supply component or interface
board has failed.
F. Swap with a harness known to be good.
If computer functions, replace the
harness.
G. If any component in the power supply
system (including the transformer and
interface board) fail, power will not be
supplied to the computer and it will not
function.
Remove and restore power to the computer.
Computer error.
Computer locks up.
A. Wait until the previous filtration cycle
ends to start another filtration cycle or
until the MIB board has reset. This may
take up to one minute.
B. If filter busy is still displayed with no
activity, ensure the filter pan is empty and
remove and restore ALL power to the
fryer.
A. Another filtration cycle is still in
process.
B. Computer error.
M3000 display shows
filter busy.
Silence the alarm by pressing the 9 button.
Check that fryer is heating properly.
Maximum recovery for electric is 1:40. If this
error continues to appear call your ASA.
M3000 display shows
RECOVERY
FAULT.
Recovery time exceeded maximum time
limit for two or more cycles.
1-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
M3000 display shows
ENERGY
MISCONFIGURED
M3000 display shows
EXCEPTION
Probable Causes
Corrective Action
Press 1234 to enter setup and set energy type
for electric.
Wrong energy type selected in setup.
Press 1234 to enter setup and reconfigure the
computer.
An error has occurred.
ERROR with the
description on the right.
Press YES to silence alarm. The error is
displayed three times. See list of issues in
section 1.14.3. Fix issue. The computer
displays SYSTEM ERROR FIXED?
YES/NO. Press YES. Computer displays
ENTER CODE. Enter 1111 to clear error
code. Pressing NO will allow the fryer to
cook but the error will be redisplayed every
15 minutes.
M3000 displays
SERVICE
REQUIREDfollowed
by the error.
An error has occurred.
M3000 display is in
wrong temperature
scale (Fahrenheit or
Celsius).
See section 1.14.2 on page 1-33 to change
temperature scale.
Incorrect display option programmed.
Change the filter pad and ensure the filter pan
has been removed from the fryer for a
minimum of 30 seconds.
Do NOT ignore CHANGE FILTER
PADprompts.
Filter error has occurred, filter pad
clogged, 24 hour filter pad change prompt
has occurred or change filter pad was
ignored on a prior prompt.
M3000 displays
CHANGE FILTER
PAD.
A. Pull filter pan out and fully reinsert into
fryer.
B. Ensure the filter pan magnet is in place
and if missing replace.
C. If the filter pan magnet is fully against
the switch and computer continues to
display INSERT pan, switch is
possibly defective.
A. Filter pan is not fully inserted into fryer.
B. Missing filter pan magnet.
C. Defective filter pan switch.
M3000 display shows
INSERT pan.
Frypot temperature is more than 410ºF
(210ºC) or, in CE countries, 395ºF
(202ºC).
This in an indication of a malfunction in the
temperature control circuitry, including a
failure of the high-limit thermostat.
M3000 display shows
hot-hi-1.
This is displayed only during a test of the
high-limit circuit and indicates that the high-
limit has opened properly.
M3000 display shows
Computer in high-limit test mode.
HI-LIMIT.
This display is normal when the fryer is first
turned on while in the melt cycle mode. To
bypass the melt cycle press and hold either #1
or #2 cook button under the LCD display
until a chirp is heard. The computer displays
EXIT MELT alternating with YES NO.
Press the #1 YES button to exit melt. If the
display continues, the fryer is not heating.
M3000 display shows
low temp
alternating with MLT-
CYCL.
Frypot temperature is between 180°F
(82°C).
M3000 display shows
ERROR RM SDCRD
Defective SD Card
Replace card with another card.
1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Probable Causes
A. Problem with the temperature
measuring circuitry including the probe.
Corrective Action
A. This indicates a problem within the
temperature measuring circuitry. Check
resistance of probe, if faulty replace
probe.
M3000 display shows B. Damaged computer wiring harness or
TEMP PROBE
connector.
B. Swap the computer wiring harness with
one known to be good. If problem is
corrected, replace the harness.
FAILURE.
MAINT FILTER
(Manual Filter) won’t
start.
Ensure fryer is at setpoint before starting
MAINT FILTER.
Temperature too low.
Remove and discard product. Press a cook
button under the display with the error to
remove the error. Reset the setpoint of the
vat before trying to cook product.
In non-dedicated mode, a product is
dropped that has a different setpoint that
the current vat temperature.
M3000 display shows
REMOVE DISCARD.
Turn off the vat with the issue. The error is
displayed if the fryer loses its ability to heat
oil. It is also displayed when the oil
temperature is above 450°F (232°C) and the
high-limit thermostat has opened, halting the
heating of the oil.
M3000 display shows
HEATING
Failed computer, failed interface board,
open high-limit thermostat.
FAILURE.
Computer will not go
into program mode or
some buttons do not
actuate.
Failed computer.
Replace computer
This is displayed during a test of the high-
limit circuit to indicate if the high-limit has
failed.
M3000 display shows
Computer in high-limit test mode.
Failed high-limit.
HI 2 BAD.
M3000 display shows
HELP HI-2 or HIGH
LIMIT FAILURE.
This is displayed to indicate the high-limit
has failed.
Check that all harnesses between M3000’s,
MIB, AIF and ATO are secure. Ensure
24VDC is present on pins 5 & 6 of J2 on
MIB board and on J4 or J5 of AIF board.
Check for loose or broken pins/wires. If the
problem persists, swap out computer from
one bank to another and cycle power on the
fryer.
M3000 display shows
software for only
M3000 or MIB but not
all boards.
Loose or damaged harness
A. Ensure all cords are fully seated in the
receptacles, locked into place and that
circuit breakers are not tripped.
B. Check three amp fuse on front of control
box.
C. Replace computer.
D. Replace computer wiring harness.
A. Three phase power cord unplugged or
circuit breaker is tripped.
B. Blown fuse
C. Failed computer.
D. Damaged computer wiring harness.
M3000 display shows
low temp,
heating
indicator cycles on and
off normally but fryer
does not heat.
E. Open connection in high-limit circuit. E. Check high limit circuit starting at the
control box connector working to the
high-limit.
1-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Probable Causes
Corrective Action
A filter error has occurred due to dirty or
clogged filter pad or paper, clogged filter
pump, filter pump thermal overload, Follow the steps in the flowchart in section
improperly installed filter pan components, 1.14.5.
worn or missing O-rings, cold oil or an
M3000 display shows
IS VAT FULL?
YES NO.
actuator problem.
Overwrite the filter after setting by re-entering
the filter after value in level two. Ensure that
the down arrow is pressed after entering the
value to save the setting (see section 4.13.5 on
page 4-33 in the BIELA14 IO Manual).
Fryer filters after each Filter after setting incorrect or software
cook cycle. update issue.
1.14.2 M3000 Useful Codes
To enter any of the following codes: Press and hold 3and 4simultaneously for TEN seconds; three chirps
sound. The computer displays TECH MODE. Enter the codes below to perform the function.
• 1658 – Change from F° to C° The computer displays off. Turn the computer on and check
temperature to see the temperature scale. If the desired scale is not displayed, repeat.
• 3322 – Reset Factory Menu The computer displays COMPLETE and then off. (NOTE:
This will delete any hand-entered menu items).
• 1650 – Enter Tech Mode. See page 1-36 to reset passwords and change filter pad time.
• 1212 – Switch between Domestic Menu and International Menu. The computer displays
COMPLETEand then off. (NOTE: This will delete any hand-entered menu items).
• 0469 – Reset FILTER STAT DATA
The following codes require the removal and reinsertion of the J3 locator plug on the rear of the computer
before entering the code.
• 1000 – Reset CALL TECH Message - Disconnect board locator plug (J3). Reinsert plug.
Enter 1000. Computer display switches to off. Remove and then restore power to the computer
using the 20-pin plug.
• 9988 – Reset BADCRC Message - Disconnect board locator plug (J3). Reinsert plug. Enter
9988. Computer display switches to off. Remove and then restore power to the computer using
the 20-pin plug.
The following codes are entered when prompted to do so or from an energy misconfigured exception error.
• 1111 – Reset SERVICE REQUIRED Message – Enter when the issue is fixed and prompted
to enter.
• 1234 – Enter SETUP MODE from energy misconfigured exception error (This usually can be
done without pressing the filter buttons if an error is displayed.)
PASSWORDS
To enter level one, level two passwords: Press and hold the TEMP and INFO buttons simultaneously until
level 1 or level 2 is displayed. Release the buttons and ENTER Codeappears.
• 1234 – Fryer Setup, Level One and Level Two
• 4321 – Usage Password (resets usage statistics).
1-33
Download from Www.Somanuals.com. All Manuals Search And Download.
1.14.3 Service Required Errors
A SERVICE REQUIRED error alternating with YES displays on the computer. After YES is pressed the
alarm is silenced. The computer displays an error message from the list below three times with the
location of the error. Then the computer displays SYSTEM ERROR FIXED? YES/NO. If yes is chosen,
enter code 1111. If NO is chosen the system returns to cook mode for 15 minutes then redisplays error
until issue is fixed.
Pressing the MIB reset button during any filter function will generate a “SERVICE REQUIRED”
error.
This is a list of the service required errors and causes.
ERROR MESSAGE
PUMP NOT FILLING
EXPLANATION
Oil not returning to vat quickly. Possible
problems: dirty pad, bad or missing O-rings,
tripped or defective filter pump, actuators or
linkage.
DRAIN VALVE NOT OPEN
DRAIN VALVE NOT CLOSED
RETURN VALVE NOT OPEN
RETURN VALVE NOT CLOSED
MIB BOARD
Drain valve failed to open; the valve’s
position is unknown.
Drain valve failed to close; the valve’s
position is unknown.
Return valve failed to open; the valve’s
position is unknown.
Return valve failed to close; the valve’s
position is unknown.
Problem with CAN communications; Check
for loose CAN connections between
computer and MIB board. MIB board failure
MIB detects AIF missing; AIF board failure
MIB detects ATO board connection lost;
ATO board failure
AIF BOARD
ATO BOARD
HIGH LIMIT FAILURE
AIF PROBE
High limit circuit has an issue
AIF RTD reading out of range
ATO PROBE
ATO RTD reading out of range
TEMP PROBE FAILURE
MIB SOFTWARE
TEMP Probe reading out of range
Internal MIB software error
INVALID CODE LOCATION
MISCONFIGURED ENERGY TYPE
SD card removed during update
Energy type in fryer setup is incorrect. (ie.
Set proper energy type gas or electric)
Press 1234 to enter setup to properly
configure fryer.
RTC INVALID DATE
The date is invalid. Press 1234 to enter
setup to properly configure fryer and set
proper date.
1-34
Download from Www.Somanuals.com. All Manuals Search And Download.
1.14.4 Error Log Codes
Refer to page 1-39, level 2 program for access to the E-log. The ten most recent errors are listed from
A-J, with A being the most recent error.
Code
ERROR MESSAGE
EXPLANATION
E01
REMOVE DISCARD (Right)
A product cook is started on the right side of a split
vat or in a full vat that has a different setpoint other
than the current vat temperature.
E02
REMOVE DISCARD (Left)
A product cook is started on the right side of a split
vat or in a full vat that has a different setpoint other
than the current vat temperature.
E03
E04
E05
ERROR TEMP PROBE FAILURE
HI 2 BAD
HOT HI 1
Temp probe reading out of range
High limit reading is out of range.
High limit temperature is past more than 410°F
(210°C), or in CE countries, 395°F (202°C)
A component has failed in the high limit circuit such
as computer, interface board, contactor or open-
high limit.
E06
HEATING FAILURE
E07
E08
ERROR MIB SOFTWARE
ERROR ATO BOARD
Internal MIB software error
MIB detects ATO board connection lost; ATO
board failure
E09
ERROR PUMP NOT FILLING
Oil not returning to vat quickly. Possible problems:
dirty pad, bad or missing O-rings, tripped or
defective filter pump, actuators or linkage.
Drain valve failed to open; the valve’s position is
unknown.
Drain valve failed to close; the valve’s position is
unknown.
Return valve failed to open; the valve’s position is
unknown.
E10
E11
E12
E13
ERROR DRAIN VALVE NOT OPEN
ERROR DRAIN VALVE NOT CLOSED
ERROR RETURN VALVE NOT OPEN
ERROR RETURN VALVE NOT CLOSED
Return valve failed to close; the valve’s position is
unknown.
E14
E15
ERROR AIF BOARD
ERROR MIB BOARD
MIB detects AIF missing; AIF board failure
Cooking computer detects MIB connections lost;
Check software version on each computer. If
versions are missing, check CAN connections
between each computer; MIB board failure
AIF RTD reading out of range
E16
E17
E18
E19
E20
E21
ERROR AIF PROBE
ERROR ATO PROBE
Not currently used
M3000 CAN TX FULL
INVALID CODE LOCATION
ATO RTD reading out of range
Connection between computers lost
SD card removed during update
FILTER PAD PROCEDURE ERROR 25 hour timer has expired or dirty filter logic has
(Change Filter Pad)
activated
E22
OIL IN PAN ERROR
The MIB has reset the oil in pan flag.
E23
E24
E25
E26
CLOGGED DRAIN (Gas)
AIF BOARD OIB FAILED (Gas)
RECOVERY FAULT
Vat did not empty during filtration
Oil is back sensor failed.
Recovery time exceeded maximum time limit.
Recovery time exceeded maximum time limit for
two or more cycles.
RECOVERY FAULT CALL SERVICE
E27
LOW TEMP ALARM
Oil temperature has dropped lower than 15°F (8°C)
in idle mode or 45°F (25°C) in cook mode.
1-35
Download from Www.Somanuals.com. All Manuals Search And Download.
1.14.5 Tech Mode
Tech mode allows technicians to reset all passwords set in levels one and two and change when the
fryer calls for a filter pad change. The default is 25 hours.
1. Press and hold 3and 4 simultaneously for TEN seconds until three chirps sound and TECH
MODEis displayed.
2. Enter 1650.
3. The computer displays CLEAR PASSWORDS.
4. Press the 9 (1) button to accept selection and clear the passwords.
5. The computer displays CLEAR PASSWORDSon the left and COMPLETEon the right.
This clears any passwords set up under levels one and two.
6. Press the ubutton to toggle to FILTER PAD TIMEon the left and 25on the right. (25
hours is the default time to change the pad)
7. Press the 8 (2) button to accept changes and exit.
8. The computer displays OFF.
1-36
Download from Www.Somanuals.com. All Manuals Search And Download.
1.14.6 M3000 Filter Error Flowchart
MESSAGE
DISPLAYED
NORMAL
OPERATION
RESUMES
Call an Authorized
Repair Technician
SIXTH
CONSECUTIVE
FILTER ERROR
TECH
ENTERS
CODE
Fryer returns to
cook mode for 15
minutes.
Change filter pad and
ensure filter pan is
pulled out for a
minimum of 30
seconds.
Fryer rrns to
cook mode for 4
minutes or 15
minutes if pad
change expired.
If the computer displays SERVICE
REQUIRED, the fryer can be used in
most cases by answering NO when the
prompt for SYSTEM ERROR
FIXED? YES NO is displayed. The
message repeats every 15 minutes until
the issue is repaired and error cleared by
a technician. To clear the error, enter
1111 after answering YES when
SYSTEM ERROR FIXED? YES
NOis displayed.
This chart follows the process of clearing a filtration
issue. The prompt is displayed when any of the
following occur:
1. a clogged filter pad,
2. a tripped or defective filter pump,
3. a leaky O-ring on the pick-up tube,
4. a failed drain valve/actuator, or
5. a failed return valve/actuator.
1-37
Download from Www.Somanuals.com. All Manuals Search And Download.
1.14.7 M3000 Menu Summary Tree
Reflected below are the major programming sections in the M3000 and the order in which submenu headings will be found
under the sections in the Installation and Operation Manual.
Adding New Menu Items
Storing Menu Items in Product Buttons
Draining, Refilling, and Disposing of Oil
See section 4.10.2
See section 4.10.3
See section 4.10.4
1-38
Download from Www.Somanuals.com. All Manuals Search And Download.
1.14.8 M3000 Board Pin Positions and Harnesses
Pin
Connector
J1
From/To
SD Card
Harness PN
#
Function
12VAC In
Voltage Wire Color
12VAC
1
2
3
4
5
6
7
8
9
Ground
12VAC In
12VAC
FV Heat Demand
V Relay
12VDC
DV Heat Demand
R/H B/L
12VDC
Black
Analog Ground
L/H B/L
12VDC
8074199
SMT Computer to
Interface Board
Harness
Interface
Board to
Computer
10 ALARM
J2
11 Sound Device
5VDC
12 ALARM
13 FV Probe
14 Common Probes
15 DV Probe
16
17
18
19
20
1
2
3
4
5
6
Vat #1
Vat #2
Vat #3
Vat #4
Vat #5
Ground
Interface
Board Ground
to Computer
Black
Computer Locator
Harness
J3
J4
Not Used
1
2
3
4
5
6
1
2
3
4
5
6
Ground
Black
Red
CAN Lo
CAN Hi
8074546
Computer
Communication
Harness
Next M3000
J7 or Network
Resistor
White
J6
J7
Ground
CAN Lo
CAN Hi
Black
Red
8074546
Computer
Communication
Harness
MIB J1 or
previous
M3000 J6
White
1-39
Download from Www.Somanuals.com. All Manuals Search And Download.
1.15
Loading and Updating Software Procedures
Updating the software takes approximately 30 minutes. The software only needs to be loaded in ONE computer and it will
update all the computers and boards in the system. To update the software, follow these steps carefully:
1. Switch all computers to OFF. Press the TEMP button to check current M3000/MIB/AIF/ATO software
version.
2. Remove the bezel and remove the two screws on the left side cover plate of the M3000 board.
3. With the computer folded down, insert the SD card, with the contacts facing down and the notch on the
bottom right (see Figure 23 and 24), into the slot on the left side of the M3000.
4. Once inserted, UPGRADE IN PROGRESSappears on the left display and WAITon the right.
5. The display then changes to CC UPDATINGon the left and the percentage completed appears on the right.
The display counts up to 100 on the right, changing to a flashing BOOT. DO NOT REMOVE THE CARD
UNTIL THE DISPLAY PROMPTS TO DO SO IN STEP 8.
6. Then UPGRADE IN PROGRESSis displayed on the left display and WAITon the right again
followed by COOK HEX, mib HEX, aif HEX ending with aTO HEX displayed on the left and the
percentage complete on the right.
7. The display then changes to REMOVE SD CARDon the left and 100on the right.
8. Remove the SD card using the fingernail slot on the top of the SD card.
9. Once the SD card is removed the display changes to CYCLE POWER.
10. Cycle the control power using the hidden reset switch behind the right control box. ENSURE THE
SWITCH IS HELD FOR 10 SECONDS. WAIT ANOTHER 20 SECONDS UNTIL THE MIB
BOARD HAS FULLY RESET BEFORE CONTINUING.
11. An EXCEPTION MISCONFIGURED ENERGY TYPEerror may appear on the left computer
while a flashing BOOTis displayed on the remaining computers while the program is transferred. If this
happens, enter 1234 on the left computer. The display changes to LANGUAGEon the left and
ENGLISHon the right. To change the entry use the < FLTR and FLTR > buttons. To navigate to the
next field, use the uINFO button. Once all parameters have been setup, press 8 (2) button to exit.
SETUP COMPLETEis displayed.
12. When the update is complete the M3000 displays OFF. The MIB display will remain blank while
software is loading, changing to show the vat numbers. Once the LED’s stop blinking, the MIB board will
display A.
13. Cycle the control power using the hidden reset switch behind the right control box again. ENSURE THE
SWITCH IS HELD FOR 10 SECONDS. WAIT ANOTHER 20 SECONDS UNTIL THE MIB
BOARD HAS FULLY RESET BEFORE CONTINUING.
14. With the computer displaying OFF, VERIFY software update by pressing the TEMP button to
check updated M3000/MIB/AIF/ATO version on each computer. IF ANY BOARDS DID NOT
UPDATE, REPEAT THE PROCESS STARTING WITH STEP 3.
15. Press and hold the two outer filter buttons until TECH MODEis displayed.
16. Enter 1650, CLEAR PASSWORDSis displayed.
17. Press the INFO button once. FILTER PAD TIMEis displayed on the left side and 25is displayed on
the right. IF ANY OTHER NUMBER OTHER THAN 25 IS DISPLAYED, ENTER 25. This only
needs to be performed on one computer.
18. Press the INFO button again.
19. Press the 8 (2) button to exit.
20. Once the software has been updated and the versions are correct, replace the cover and screws covering the
SD card slot.
21. Reinstall the screws attaching the computers and bezel by reversing steps 2 through 5.
22. Perform a forced auto filter cycle on each vat except the fish vat by pressing and holding one of
the filter buttons. FILTER MENUis displayed changing to AUTO FILTER.
23. Press the (1 9) button.
24. FILTER NOW YES/NOis displayed.
25. Press the (1 9) button.
26. SKIM VATis displayed changing to CONFIRM.
27. Press the (1 9) button. The auto filter cycle should start.
28. Once the filter cycle is complete, repeat on each vat in
the fryer.
29. Once all vats have been successfully filtered the
software update is finished.
Figure 23
Figure 24
1-40
Download from Www.Somanuals.com. All Manuals Search And Download.
1.16 BIELA14 Series LOV™ Data Network Flowchart
1-41
Download from Www.Somanuals.com. All Manuals Search And Download.
1.17 Interface Board Diagnostic Chart
The following diagram and charts provide ten quick system checks that can be performed using only a
multimeter.
Diagnostic LED Legend
CMP indicates power from 12V transformer
24
HI
indicates power from 24V transformer
(RH) indicates output (closed) from right latch
relay
HI
(LH) indicates output (closed) from left latch
relay
HT
HT
AL
(RH) indicates output from right heat relay
(LH) indicates output from left heat relay
(RH) indicates output (open) from right latch
relay
AL
(LH) indicates output (open) from left latch
relay
PN 826-2260 (106-6664)
NOTE – Pin is located in the bottom right corner of
Both J1 and J2. These test points are ONLY for LOV™
Series boards with J1 and J2 plugs on the front of the board.
Meter Setting
12 VAC Power
24 VAC Power
Test
50 VAC Scale
50 VAC Scale
R X 1000 OHMS
R X 1000 OHMS
R X 1 OHMS
R X 1 OHMS
R X 1 OHMS
R X 1 OHMS
R X 1 OHMS
R X 1 OHMS
Pin
3 of J2
2 of J2
Pin
Results
1 of J2 12-16 VAC
Chassis 24-30 VAC
*Probe Resistance (RH)
*Probe Resistance (LH)
High-Limit Continuity (RH)
High-Limit Continuity (LH)
Latch Contactor Coil (RH)
Latch Contactor Coil (LH)
Heat Contactor Coil (RH)
Heat Contactor Coil (LH)
11 of J2 10 of J2 See Chart
1 of J1
9 of J2
6 of J1
8 of J2
5 of J1
7 of J2
4 of J1
2 of J1 See Chart
6 of J2 0 - OHMS
9 of J1 0 - OHMS
Chassis 3-10 OHMS
Chassis 3-10 OHMS
Chassis 11-15 OHMS
Chassis 11-15 OHMS
* Disconnect 15-Pin harness from the computer before testing the probe circuit.
1-42
Download from Www.Somanuals.com. All Manuals Search And Download.
1.18 Probe Resistance Chart
Probe Resistance Chart
For use with fryers manufactured with Minco Thermistor probes only.
F
60
65
70
75
80
85
90
OHMS
1059
1070
1080
1091
1101
1112
1122
1133
1143
1154
1164
1174
1185
1195
C
F
OHMS
1204
1216
1226
1237
1247
1258
1268
1278
1289
1299
1309
1320
1330
1340
C
F
OHMS
1350
1361
1371
1381
1391
1402
1412
1422
1432
1442
1453
1463
1473
1483
C
F
OHMS
1493
1503
1514
1524
1534
1544
1554
1564
1574
1584
1594
1604
1614
1624
C
F
OHMS
1634
1644
1654
1664
1674
1684
1694
1704
1714
1724
1734
1744
1754
1764
C
16
18
21
24
27
29
32
35
38
41
43
46
49
52
130
135
140
145
150
155
160
165
170
175
180
185
190
195
54
57
60
63
66
68
71
74
77
79
82
85
88
91
200
205
210
215
220
225
230
235
240
245
250
255
260
265
93
96
99
270
275
280
285
290
295
300
305
310
315
320
325
330
335
132
135
138
141
143
146
149
152
154
157
160
163
166
168
340
345
350
355
360
365
370
375
380
385
390
395
400
405
171
174
177
179
182
185
188
191
193
196
199
202
204
207
102
104
107
110
113
116
118
121
124
127
129
95
100
105
110
115
120
125
1-43
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19 Wiring Diagrams
1.19.1 Component Wiring (Domestic)
1-44
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.2 Component Wiring (CE)
1-45
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.3 Component Wiring (CSA)
1-46
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.4 Component Wiring (Australia)
1-47
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.5 Contactor Box – Delta Configuration
1-48
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.6 Contactor Box – WYE Configuration
1-49
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.7 Simplified BIELA14 LOV™ Gen II Series – Full Vat Delta Wiring
1-50
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.8 Simplified BIELA14 LOV™ Gen II Series – Dual Vat Delta Wiring
1-51
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.9 Simplified BIELA14 LOV™ Gen II Series – Full Vat Wiring EXPORT WYE
1-52
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.10 Simplified BIELA14 LOV™ Gen II Series – Dual Vat Wiring EXPORT WYE
1-53
Download from Www.Somanuals.com. All Manuals Search And Download.
1.19.11 BIELA14 Gen II Series LOV™ Simplified Wiring
1-54
Download from Www.Somanuals.com. All Manuals Search And Download.
BIELA14 SERIES GEN II LOV™ ELECTRIC FRYERS
CHAPTER 2: PARTS LIST
2.1 Accessories
ITEM
PART #
809-0171
809-0402
810-2793
809-0921
803-0398
823-7263
106-8325
106-8329
803-0132
803-0106
803-0388
COMPONENT
Thumbscrew, ¼ -20 X 1⅜-inch Universal Hood
Thumbscrew, ¼ -20 X ½-inch Cap-N-Splash Hood
Hanger, Wireform Basket
Spacer, Basket Hanger
Brush, Frypot
Connecting Strip, Frypot
Cover, Full-Vat Frypot
Cover, Dual-Vat Frypot
1
2
*
3
4
5
*
6
7
8
Rack, Full-Vat Basket Support
Rack, Dual-Vat Basket Support
Element Lift / Fryers Friend LOV™
*Not illustrated.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Doors, Sides, Tilt Housings, Cap-N-Splash, Top Caps and Casters
ITEM
PART #
231-0323
232-0323
810-1105
108-0915
230-4960
106-4067
810-0275
809-0970
230-7192
220-6097
810-0327
810-0326
COMPONENT
Side, Standard Cabinet Left SS (use 221-0323 for Enameled Steel)
Side, Standard Cabinet Right SS (use 222-0323 for Enameled Steel)
Magnet, Door (vertical) (use 810-2346 for horizontal over filter pan)
Door, Left or Right (Left shown – move handle to bottom for right)
Handle, Eurolook Door
1
2
3
4
5
6
*
*
*
*
7
8
9
Pin Assembly, Door
Spring, Door Pin
Retaining Ring
Hinge, Door Lower
Holder, Manual
Caster without Brake
Caster with Brake
Tilt Housing (Housing for five station fryer shown)
Two Station, S/S (use 108-0131 for Aluminized Steel) (910-2441 Hoodstrip)
Three Station, S/S (use 108-0132 for Aluminized Steel) (910-2440 Hoodstrip)
Four Station, S/S (use 108-0133 for Aluminized Steel) (910-2439 Hoodstrip)
Five Station, S/S (use 108-0138) for Aluminized Steel) (910-9447 Hoodstrip)
Cap-N-Splash
823-6085
823-5700
823-6151
823-6243
10
11
823-6420
823-6421
823-6422
823-6887
Two Station
Three Station
Four Station
Five Station
Top Cap (Top cap for five station fryer shown)
Two Station (Also requires four 809-0078 10-32 Nutserts)
Three Station (Also requires six 809-0078 10-32 Nutserts)
Four Station (Also requires eight 809-0078 10-32 Nutserts)
Five Station (Also requires ten 809-0078 10-32 Nutserts)
106-7835
106-5979
106-7576
106-7841
* Not illustrated.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Drain System Components
2.3.1 Drain Tube Sections and Associated Parts
See Section 2.3.2 for Drain Valves
ITEM
PART#
823-6020
823-6112
108-1874
108-1876
108-1878
823-6019
823-6021
823-6240
823-6242
823-6202
823-6114
823-6117
823-6115
816-0772
809-0969
816-0630
810-3531
COMPONENT
Drain Tube, Full-Vat Left Closed/Right End Open
Drain Tube, Dual-Vat Left Closed/Right End Open
Drain Tube, Dump (Use 108-1882 for French Unit)
Drain Tube, Full-Vat 2 Bat. Dump Left Closed/Right End Open
Drain Tube, Dual-Vat 2 Bat. Dump Left Closed/Right End Open
Drain Tube, Full-Vat Left and Right Open
Drain Tube, Dual-Vat Left and Right Open
Drain Tube, Full-Vat 2 Bat. Left Open/Right End Closed
Drain Tube, Dual-Vat 2 Bat. Left Open/Right End Closed
Drain Tube, Full-Vat Left Open/Right End Closed
Drain Tube, Dual-Vat Left Open/Right End Closed
Drain Tube, Full-Vat Left and Right Open
Drain Tube, Dual-Vat Left and Right Open
Sleeve
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
*
Clamp
Vinyl Cap
Valve, Check 20 PSI RTI bypass
*
* Not illustrated.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3.2
Drain Valves and Associated Parts
2.3.2.1 Linear Actuator Drain Valves
ITEM
PART #
809-0540
900-2936
232-5701
231-5701
824-2048
824-2047
222-5962
816-0544
823-7231
823-7230
COMPONENT
1
2
3
4
5
6
7
8
9
Nut, ½-13 2-Way Hex Lock
Retainer, Nut Drain Valve
Handle, Drain Valve FV or DV Right
Handle, Drain Valve DV Left
Mount, Electric Drain Actuator Right
Mount, Electric Drain Actuator Left
Bracket, Drain to Valve LOV™ Electric
O-Ring, Round Drain Seal
Valve, 1¼-inch Drain LOV™ Electric Right
Valve, 1¼-inch Drain LOV™ Electric Left
10
2.3.2.2 Rotary Actuator Drain Valves
ITEM
PART #
810-3755
COMPONENT
Valve, 1¼-inch NPT Rotary Actuator
1
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4
Electronics and Wiring Components
2.4.1 Component Boxes
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.1 Component Boxes cont.
ITEM
PART #
106-5592
200-3300
COMPONENT
Box Assembly, Component
Bracket, Component Box Strain Relief
1
2
3
806-9495SP Terminal Block
√ 4
√ 5
6
807-4346
807-4482
807-0037
807-0121
807-0922
807-2278
810-2446
807-4036
807-3575
807-1947
807-1321
807-1597
810-2445
106-5750
106-5751
807-0855
807-0800
807-4933
Relay, 120V DPDT 20A (used in Canadian models only)
Relay, Filter 2 Pole 30A DPDT 24VDC
Terminal, ¼-inch Push-on
Bushing, Heyco Plastic AB-625-500
Holder, Buss Fuse HPS Screw Type
Fuse, 20 Amp
Plug, Button .50 Heyco Double “D”
Switch, Power
Plug, Carling Switch Hole (used on some models without a switch)
Plug, Button .875 Dome
Holder, AGC Panel Mount ¼” Fuse (Some models use item 10 here.)
Fuse, 3 AMP Slow-Blow
Plug, Button .625 Heyco Double “D”
Harness Assembly, RE FV Control
Harness Assembly, RE DV Control
7
8
9
10
√ 11
12
13
14
15
16
√ 17
√ 18
√
Transformer, 100-120V/12V 20VA
Transformer, 100-120V/24V 50VA Filter (Used in FV component boxes)
Transformer, 120/208/240V/24V 75VA Filter (Used in DV component
boxes)
√ 19
√ 20
√ 21
√ 22
23
807-2181
807-2191
807-0979
807-2180
809-0349
Transformer, 100-120V /24V 62VA Filter
Transformer, 208-240V/12V 30VA
Transformer, 208-240V/12V 43VA
Transformer, 100-120V 50VA Filter
Spacer, 4mm X 6mm Aluminum
24
Interface Board
√
826-2260
807-4403
220-4723
807-4678
230-5038
816-0217
810-0045
200-6654
807-4346
Standard Full or Dual Vat Interface Board (includes sound harness)
Speaker, 4-Watt SMT
Guard, Finger w/ switch opening
Switch, Momentary Flush JIB Reset
Guard, RE Box Switch
Paper, Insulating Terminal Block
*
25
26
27
28
29
30
Bushing, .875 Diameter 11/16”
Brace, Component Box
√ 31
Relay, DPDT 20A 120V (used for control power reset in right hand boxes
only in domestic and Canadian units)
Relay, DPDT 20A 240V (used for control power reset in right hand boxes
only in international units; some international units have one located in
each control box)
807-4770
32
*
807-2659
826-2249
Switch, Momentary (used to reset control power; located in box over JIB
only.)
RE Hood/Ansul Interlock Kit (includes terminal block, wires and connectors)
* Not illustrated.
√ Recommended parts.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.2
Contactor Boxes
2.4.2.1 Left and Right Contactor Box Configurations
6
STANDARD
MECHANICAL
LEFT AND RIGHT
CONFIGURATIONS
7
2
1
8
9
5
7
5
10
120/440/480v
LEFT AND RIGHT
STANDARD AND
MECHANICAL
CONFIGURATIONS
2
1
5
7
5
6
2
6
CANADIAN 14kW RIGHT
CONFIGURATIONS
3
4
LEFT HAND
BOX COVER
RIGHT HAND
BOX COVER
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.2.1 Left and Right Contactor Box Configurations cont.
NOTES: Left and right contactor box assemblies are mirror images of one another. With the
exception of the box itself, all components of a left-hand assembly are the same as those in the
corresponding right-hand assembly and vice versa except for the hood relay which occurs in the
right or large box only. The configurations illustrated show all possible components, but a particular
configuration may not have all the components shown.
ITEM
PART #
106-8658
106-8660
221-0482
222-0482
807-0070
807-2284
810-1202
807-1683
807-0922
807-2278
807-0064
221-0610
222-0610
807-4316
807-4317
807-0012
COMPONENT
Box Assembly, Left Contactor
Box Assembly, Right Contactor
Cover, Left Hand Contactor Box
Cover, Right Hand Contactor Box
Terminal, Ground Lug
Contactor, 24V 50 Amp Mechanical (Heat)
Contactor, 24V 40 Amp Mechanical (Latch)
Relay, Hood 12VDC
1
2
3
4
9
√ 5
√ 6
7
8
9
10
*
*
*
*
*
Holder, Bus Fuse
Fuse, 20 Amp
Transformer, 480V/120V 150VA
Bracket, Left Hand Contactor Box Mounting
Bracket, Right Hand Contactor Box Mounting
McDonald’s Cordset, 120V 5-Wire
McDonald’s Cordset, Europe 3-Wire Single Phase
Relay, Tilt Switch 18 Amp 1/3 HP 24 V Coil
* Not illustrated.
√ Recommended parts.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.3
Heating Element Assemblies and Associated Parts
2.4.3.1 Element Assemblies and Hardware
NOTE: These elements apply only to BIELA14 Gen II Series Fryers.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.3.1 Element Assemblies and Hardware cont.
ITEM
PART #
COMPONENT
1
Element
826-2198
200V 7.0 kW (220V 8.5kW used in some export 3-phase 4-wire WYE
units)
√
826-2192
826-2200
208V 17.0 kW
220V 17.0 kW (240V 8.5kW used in some export 3-phase 4-wire WYE
units)
826-2193
826-2199
230V 17.0 kW
230V/400V 7.0/8.5 kW (used in some export 3-phase 4-wire WYE
units)
826-2194
826-2196
826-2212
816-0681
816-0480
816-0688
809-1003
809-0766
230-4028
230-3714
240V 17.0 kW
480V 17.0 kW
Probe, Temperature RE – includes tie wraps and grommet.
Grommet, Probe
Plug, .375-inch Dome
√ 2
3
4
5
6
*
*
7
Gasket, Element
Screw, 10-32 X ⅜-inch Hex Head SS
Nut, 10-32 Keps Hex Head SS
Wrench, Element Tube Nut Spanner
Bracket, Temperature Probe 7.0kW
Bracket, Temperature Probe 8.5kW (used in some export 3-phase 4-wire
WYE units)
230-0784
8
9
220-0464
910-2042
230-0781
230-4902
230-4101
809-0567
230-4903
230-4103
810-3030
810-3131
220-0733
Bracket, Lower Spring
Clamp, Element (Short)
Clamp, Element (Long)
Support, Full-Vat Element Rear
Support, Full-Vat Element Front
Tie-Wrap, Metal
Support, Dual-Vat Element Bottom Rear
Support, Dual-Vat Element Bottom Front
Spring, Element Lift Left
10
11
12
13
14
15
16
Spring, Element Lift Right
Bracket, Lower Spring Mating
17
* Not illustrated.
√ Recommended parts.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.3.2 Element Tube Assemblies
FULL-VAT ELEMENT ASSEMBLY
1
6
7
10
9
8
5
11
4
3
2
DUAL-VAT ELEMENT ASSEMBLY
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.3.2 Element Tube Assemblies contd.
ITEM
PART #
COMPONENT
1
2
108-0297SP Tube Assembly RE Element, Full-Vat
108-0298SP Tube Assembly RE Element, Dual-Vat
3
4
5
6
7
8
9
10
11
*
810-3246
108-0315
108-0316
220-0122
220-0123
106-7651
106-7652
810-2992
810-2993
826-2598
807-4742
Bushing and Tube Assembly, Dual-Vat
Bracket Assembly, LH Element Tube Support
Bracket Assembly, RH Element Tube Support
Plate, Element Tube Support Inner
Plate, Element Tube Support Outer
Bracket Assembly, LH Upper Spring (use 106-6569 for 17kW)
Bracket Assembly, RH Upper Spring (use 106-6570 for 17kW)
Tube, Full Vat Element Mounting
Bushing, Tube End Teflon
Kit, Tilt Switch
*
Switch, Long Lever High Temp
* Not illustrated.
2.4.4 Computers
NOTE: See Page 2-16 for Interface Board to Computer Wiring Harness
ITEM
PART #
COMPONENT
Replacement Computer
√
108-1295
Non-CE Domestic M3000 (For use in US, Canada, Mexico and all
other non-CE countries)
√
108-2970
807-4403
CE M3000 (For use in European CE countries)
M3000 Speaker SMT
*
* Not illustrated.
√ Recommended parts.
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.5
Wiring
2.4.5.1 Contactor Box Wiring Assemblies – 12-Pin Dual-Vat C-1
ITEM
PART #
COMPONENT
106-5980SP Contactor Box Harness Assembly Dual Vat
Standard (See wiring diagrams on pages 1-41 thru 1-43.)
1
2.4.5.2 Contactor Box Wiring Assemblies – 12-Pin Full-Vat C-1
1
GREEN/YELLOW 75C
2
3
BLUE 74C
4
5
6
1
7
ORANGE 76C
8
ORANGE 71C
9
10
11
12
ITEM
PART #
COMPONENT
106-6031SP Contactor Box Harness Assembly Full Vat
Standard (See wiring diagrams on pages 1-41 thru 1-43.)
1
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.5.3 Contactor Box Wiring Assembly – 6-Pin (Left Element)
ITEM
PART #
COMPONENT
1
106-8744 14/17 kW Mechanical Contactor
2.4.5.4 Contactor Box Wiring Assembly – 9-Pin (Right Element)
ITEM
PART #
COMPONENT
1
106-8745 14/17 kW Mechanical Contactor
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.5.5 Main Wiring Harnesses
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.5.6 Component Box and Filter Pump Wiring Harnesses
ITEM
PART #
COMPONENT
1
2
3
106-5750SP Full Vat Control Harness J4 to J2 (Standard)
106-5751SP Dual Vat Control Harness J4 to J1 and J2 (Standard)
108-0490 Filter Pump C2 to Component Box Wiring Harness
2.4.5.7 Interface Board to Controller Wiring Harness – 15-Pin
PN 807-4199
SMT Controller to Interface
Board Wiring Harness
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.5.8 M3000, MIB, AIF and ATO Wiring Harnesses
ITEM
PART #
807-4546
807-4547
COMPONENT
*
*
Computer Communication (used from Computer to Computer)
AIF Communication/Power (used from MIB to AIF and AIF to AIF)
MIB Power/Blue LED/Pan Sw (used from Transformer and Fltr Rly to
MIB to Blue LED and Pan Sw)
*
807-4649
*
*
*
807-4655
826-2569
807-4553
FV/DV Harness RTD Medium (used from RTD to ATO Board)
FV/DV ATO/RTD Probe Kit
ATO Power (used from Transformer to ATO Board)
ATO Pump and JIB (used from ATO Board to Top-off Pump and JIB
Reset Switch)
*
807-4671
ATO Pump and JIB (used from ATO Board to Top-off Pump and JIB
Reset Switch) 4-5 Battery only
ATO Yellow LED (used from ATO Board to Yellow LED)
ATO Yellow LED (used from ATO Board to Yellow LED) 4-5 Battery
only
*
*
*
807-4772
807-4555
807-4722
Computer Locator Wire (used from Computer to Interface Board) See
wiring diagram 805-1734 for locator pin positions.
Communications Terminator (used on Computer pin J6 and ATO
board pin J10 to terminate network)
*
*
807-4573
807-4552
807-4657
Jumper (used on 4 and 5 battery ATO board plug J5 pin 7 and 8)
*
*
106-9256SP Long Top-off Power (used between Component Box to ATO Box)
807-4760 Harness, LOV™ RTI-MIB connector
807-4660PK SMT Pin Service Repair Kit
230-2345 SMT Pin Extractor
√
√
*
*
* Not illustrated.
See page 1-14, 1-18, 1-27 and 1-36 for Pin Positions.
√ Recommended parts.
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5
Filtration System Components
2.5.1 Filtration Components
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.1 Filtration Components cont.
ITEM
PART #
823-7181
823-6684
823-7187
823-6162
823-7186
810-3276
810-3288
810-3268
810-3289
200-2240
220-2901
COMPONENT
Lid, Multi-Vat Fryers, Standard Size Filter Pan
Lid, Multi-Vat Fryers, Standard Size Filter Pan (France Only)
Lid, Two-Vat Fryer, Half Size Filter Pan
Lid, Two-Vat Fryer, Half Size Filter Pan (France Only)
Guard, Pan Splash Lid
Crumb Tray, Standard Size Filter Pan 3, 4 and 5 Vat
Crumb Tray, Two-Vat Fryer, Half Size Filter Pan
Hold-Down Ring for Pad 16.56 x 22.32, Standard Size Pan 3, 4, and 5 Vat
Hold-Down Ring for Pad 11.20 x 19.10, Two-Vat Fryer, Half Size Filter Pan
SanaGrid Filter Screen, Standard Size Filter Pan
1
1a
2
3
4
5
SanaGrid Filter Screen, Two-Vat Fryer, Half Size Filter Pan
106-8677SP Pan, One-Piece Filter LOV™ Standard Size
106-9148
Pan, One-Piece Filter LOV™ Standard Size (France Only)
106-8211SP Pan, Two-Vat Fryer, LOV™ Half Size
106-8435
823-6715
823-6164
823-6399
810-3007
Pan, Two-Vat Fryer, LOV™ Half Size (France Only)
6
Suction Tube Standard LOV™
Suction Tube Standard LOV™ (France Only)
Suction Tube Two Vat LOV™
Magnet, Pull Ring
7
8
106-9251SP Assembly, Filter Pan Switch Three Vat or more (106-5876SP Sensor only)
106-8080SP Assembly, Filter Pan Switch Two Vat (106-5876SP Sensor only)
106-5876SP Sensor, Magnet
230-3936
220-3748
220-3275
220-3749
106-8487
*
9
10
Rail, Filter Pan Retaining Standard
Support, Left Filter Pan
Support, Left Filter Pan Two Vat LOV™
Support, Right Filter Pan
Support, Right Filter Pan Two Vat LOV™
Motor and Gasket Kit
11
12
826-1785
826-1712
826-1756
826-1270
826-1755
826-2789
807-11973
809-1020
813-0165
810-1668
810-1067
810-1057
810-0667
810-3738
813-0031
813-0062
826-1392
813-0568
807-1105
807-1098
100V 50/60 Hz
115V 50/60 Hz
208V 50/60 Hz
220-240V 50/60 Hz
√
√
250V 50/60 Hz
13
*
*
Pump, Viking 8 GPM Kit (includes gasket 816-0093)
Viking Pump Seal Kit
Cap Screw, 5/16-inch-18 5.50” NC Hex (Connects pump to motor.)
Elbow, ST ½-inch x ½-inch NPT 90° BM
Adapter, ⅝-inch to ½-inch NPT Male
Flexline, 8.5-inch Oil Return
Flexline, 13-inch Oil Return
Check Valve ½” NPT
Adaptor, Check Valve Close Nipple
Bushing, ¾” NPT x ½” BM
Elbow, ½-inch x ½-inch 90° BM
O-Ring (Pkg. of 5; used with Item 5)
Plug, ⅛-inch Socket Head Pipe (used with Item 5; two required)
Heater Strip Assembly, 100-120V 25W 18”
Heater Strip Assembly, 208-250V 25W 18”
14
15
16
17
18
19
20
21
√ *
*
*
*
* Not illustrated.
√ Recommended parts.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.2 Auto Intermittent Filtration Components
2.5.2.1 LOV™ Indicator Lights Assembly
106-8231SP LOV™ Panel Assembly
ITEM
PART #
COMPONENT
1
2
3
106-8106SP Light, Blue 24VDC LED Flush
106-8105SP Light, Yellow/Orange 24VDC LED Flush
230-4271 Plate, Control Frame LOV™
2.5.2.2 Manual Interface Board Assembly
108-1298 Manual Interface Board Assembly
ITEM
PART #
108-1298
220-6288
108-2156
807-4481
220-5793
COMPONENT
Assembly, MIB
Cover, MIB
1
√
2
Assembly, MIB Computer w/ Frame
Overlay
3
Assembly Back, Box MIB
√ Recommended parts.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.2.3 AIF Board Assembly
6
5
4
2
1
108-1305 AIF Board Assembly
3
ITEM
PART #
108-1305
824-1988
816-0814
816-0815
108-1304
816-0820
108-0097
COMPONENT
Assembly, AIF
1
2
3
Cover, AIF Board
Gasket, AIF Board
Gasket, Computer Board
Board, AIF
Seal, AIF Board
Panel Assembly, AIF Box
√
4
5
6
√ Recommended parts.
2.5.2.4 LOV PCB/Computer Board Matrix
COMPONENT
Assembly, MIB PCB w/ metal work
Assembly, AIF Board w/ metal frame
Board, AIF Board PCB w/ software
Board, ATO PCB w/ software
M3000 Non-CE Domestic (For use in US, Canada, Mexico and
all other non-CE countries)
PART #
108-2156
108-1305
108-1304
108-1279
108-1295
108-1283
M3000 CE (For use in European CE countries)
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6
Frypot Assemblies and Associated Parts
2.6.1 Frypots with Linear Actuators
See Page 2-5 for Drain
Valve Assemblies.
See Page 2-24 for Return
Valve Assemblies.
ITEM
PART #
823-7436
823-7437
COMPONENT
1
2
Frypot, Full-Vat LOV™
Frypot, Dual-Vat LOV™
√
3
Thermostat Assembly, High-Limit Long Standard
Non-CE Full Vat 425°F (218°C) (17kW FV and 14kW FV) (Color Coded
Black 806-7543)
826-2454
826-2456
826-2455
Non-CE Dual Vat 435°F (224°C) (22kW, 17kW DV and 14 kW DV)
(Color Coded Red 806-8035)
CE Full and Dual Vat 415°F (213°C) (14kW and 17kW CE) (Color-Coded
Yellow 806-8132)
√
√
4
5
6
7
8
826-2706
810-1067
810-1668
826-2587
809-1012
809-1035
809-1036
810-1776
108-0698
108-0697
108-0700
108-0699
813-0022
813-0165
220-5960
Probe, Temperature and Fitting Kit AIF/RTD
Flexline, ⅝” OD x 8.50” Long
Adaptor, Male ⅝” OD x ½”
Actuator, Linear AIF 24VDC Kit includes 810-1776
Pin, Clevis, ¼” x 1¼” (Drain and return valves)
Pin, Clevis, ¼” x 2¼” (center pin drain actuator)
Pin, Clevis, ¼” x 2” (center pin return actuator)
Clip, Toaster Ring
Valve, Drain Assy. LOV™ FV or DV Right as viewed from front of frypot.
Valve, Drain Assy LOV™ DV Left as viewed from front of frypot.
Valve, Return Assy LOV™ FV or DV Right as viewed from front of frypot.
Valve, Return Assy LOV™ DV Left as viewed from front of frypot.
Nipple, ½” x Close NPT BM
9
10
11
12
13
14
15
16
17
18
Elbow, St. ½” x ½” NPT 90°
Strap, Elec LOV™ Actuator
√ Recommended parts.
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6.2 Frypots with Rotary Actuators
ITEM
PART #
823-7672
823-7673
COMPONENT
1
2
Frypot, Full-Vat LOV™
Frypot, Dual-Vat LOV™ (use 823-7745 for Hybrid Fish Vat)
Thermostat Assembly, High-Limit Long Standard
Non-CE Full Vat 425°F (218°C) (17kW FV and 14kW FV) (Color Coded
Black 806-7543)
√
3
826-2454
826-2456
826-2455
Non-CE Dual Vat 435°F (224°C) (22kW, 17kW DV and 14 kW DV)
(Color Coded Red 806-8035)
CE Full and Dual Vat 415°F (213°C) (14kW and 17kW CE) (Color-Coded
Yellow 806-8132)
√
4
5
6
7
8
826-2706
810-1067
810-1668
807-4961
807-4962
810-3755
810-3754
813-0022
813-0062
220-7386
Probe, Temperature and Fitting Kit AIF/RTD
Flexline, ⅝” OD x 8.50” Long
Adaptor, Male ⅝” OD x ½”
Actuator, Rotary 24VDC (#1)
Actuator, Rotary 24VDC (#2)
Valve, 1¼ Drain Rotary Actuator LOV™
Valve, ½ NPT Return Rotary Actuator LOV™
Nipple, ½” x Close NPT BM
Elbow, ½” Blk 90°
Strap, Round Drain Elec LOV
√
√
√
√
9
10
11
12
13
√ Recommended parts.
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Oil Return Manifolds
ITEM
PART #
COMPONENT
1
2
3
4
*
810-3015 Manifold, Two-Station Fryer
810-3016 Manifold, Three-Station Fryer
810-3017 Manifold, Four-Station Fryer
810-3018 Manifold, Five-Station Fryer
813-0907 Cap, 15/16-inch Valve
* Not illustrated.
2.8 Return Valves and Associated Parts
2.8.1 Return Valves and Associated Parts (Linear Actuators)
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8.1 Return Valves and Associated Parts (Linear Actuators) cont.
ITEM
PART #
232-5702
231-5702
900-2935
810-2201
823-7233
823-7232
230-5963
COMPONENT
Handle, Return Valve with Locator FV or DV Right
Handle, Return Valve with Locator DV Left
Retainer, Nut Oil Return Valve
Valve, ½-inch Ball
Mount, Return Actuator Right
1
2
3
4
5
6
7
Mount, Return Actuator Left
Brace, Return Actuator Bracket
2.8.2 Return Valve (Rotary Actuators)
Full-Vat or Dual-Vat Return Valve
ITEM
PART #
810-3754
COMPONENT
Valve, ½-inch NPT Rotary Actuator
1
2.9
Auto Top Off Components
2.9.1 JIB Basket
ITEM
PART #
220-7991
COMPONENT
1
Basket, JIB LOV™
2.9.2 JIB Cap and Pick Up Assembly
ITEM
PART #
108-2005
108-2001
810-3823
COMPONENT
Cap, JIB Assembly (use 108-2047 for BIB)
Cap, JIB (use108-2002 for Intl. BIB)
Hose, JIB
1
2
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9.2 JIB Cap and Pick Up Assembly cont.
ITEM
PART #
823-7738
816-0870
COMPONENT
3
4
Inlet, Oil Reservoir Tube
Clamp
2.9.3 Automatic Top Off Board Assembly
1
3
8
9
4
2
6
7
5
108-0506SP 120V Assy
108-0507 208-240V Assy
COMPONENT
ITEM
PART #
1
2
3
108-0653
220-5679
108-1279
Box, Assembly Auto Top Off Board
Cover, Top Off Board Box
PCB Board, Automatic Top Off
√
PCB Board, LON Works 120V (Must be pre-programmed before
shipping)
PCB Board, LON Works 230-240-250V (Must be pre-programmed before
shipping)
*
108-1302
108-1303
*
√
√
√
√
4
5
6
7
8
*
9
807-2181
807-0855
807-2180
807-2191
807-1321
807-1597
807-0012
Transformer, 100-120V/24V 62VA
Transformer, 120V 50/60-12V 20VA
Transformer, 208-240V/24V 50VA
Transformer, 208/230/240 -12V 30VA
Holder, Fuse AGC Panel Mount ¼”
Fuse, 3A Slow-Blow
√
√
Relay, 18AMP 1/3 HP 24V Coil (Top off pump)
* Not illustrated.
√ Recommended parts.
NOTE: Top off boxes for vats 4 and 5 have either item 4 or item 6, both have item 3.
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9.4 ATO Pump Assembly
Domestic Units
Item 2 connects
to a check valve
JIB hose
connects here.
before
going
into the oil
return manifold.
International Units
JIB hose
connects here.
ITEM
PART #
108-0639
810-3265
810-3591
810-0667
810-1069
COMPONENT
√
1
2
Pump, Shurflo 24VAC
Flexline, ½” OD x 24-inch (Out to oil return manifold)
Flexline, ½” OD x 8-inch (Out to oil return manifold two battery only)
Check valve, ½ NPT 1 PSI
Flexline, ⅝” OD x 29.5-inch (In from RTI fresh oil solenoid) Domestic
units only
*
3
4
5
6
7
8
810-3666
816-0782
813-0940
810-3770
813-0543
813-0838
813-0530
813-0304
813-0022
813-0345
810-1668
812-2083
811-1166
Fitting, Shurflow Pump
O-Ring, Viton #111
Elbow, ¼” NPT x ⅜ Flare
Fitting, ¼” NPT Male Barb
Elbow, ¼” NPT BM
Nipple, ¼” NPT BM Close
Tee, Reducing ½” x ¼” x ½”
Bushing, ½” x ¼” BM Flush
Nipple, ½” x Close NPY BM
Elbow, ½” BM 45°
Adaptor, Male ⅝” OD x ½”
Hose LOV Fryer JIB (Cut and attach to item 7 with a ty wrap)
Hose, Silicone Braided 18” (sold by the foot)
9
10
11
12
13
14
15
*
* Not illustrated.
√ Recommended parts.
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9.5 ATO Pump Assembly Service Kit (Larger Top Off Lines)
Item 2 connects
to a check valve
before going
into the oil
return manifold.
JIB hose
connects here.
2
13
7
1
10
3
Item 3 on this page
and Item 8 on the
following page are
the same part.
8
9
6
4
11
7
INSTALL
O-RINGS
HERE
12
5
ITEM
PART #
108-3041
108-0639
810-3265
810-3591
810-0667
810-1069
COMPONENT
Kit, Pump BIELA Topoff Service Kit
Pump, Shurflo 24VAC
√
1
2
Flexline, ½” OD x 24-inch (Out to oil return manifold)
Flexline, ½” OD x 8-inch (Out to oil return manifold two battery only)
Check valve, ½ NPT 1 PSI
Flexline, ⅝” OD x 29.5-inch (In from RTI fresh oil solenoid) Domesti
units only
*
3
4
5
6
7
8
810-3666
816-0782
813-0940
813-0062
813-0087
823-8063
813-0165
813-0247
108-2054
810-1668
813-0907
Fitting, Shurflow Pump
O-Ring, Viton #111
Elbow, ¼” NPT x ⅜ Flare
Elbow, ½” BLK 90° NPT BM
Nipple, ½” x 1.50-inch
JIB Connection Topoff Welded Assy.
Elbow, Street ½” x ½” NPT 90° BM
Nipple, ½” x 3.50-inch NPT BM
Fitting Assy Shurflow
Adaptor, Male ⅝” OD x ½”
Cap 15/16”
9
10
11
12
13
*
* Not illustrated.
√ Recommended parts.
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 RTI
2.10.1 RTI Manifold and Accessories
TO DRAIN
DOWNSPOUT
10
1
19
14
13
17
6
14
TO TOP OFF
TO OIL
11
14
PUMP INTAKE
RETURN
AND TO FILL
MANIFOLD
8
RTI JIB
6
12
21
FRESH OIL
FROM RTI
TANK
4
WASTE OIL TO RTI
DISPOSE TANK
27
6
TO OIL RETURN
MANIFOLD
3
14
22
9
TO TOP OFF
PUMP INTAKE
AND TO FILL
25
RTI JIB
8
20
2
18
5
13
23
7
16
15
24
26
TO RTI BYPASS CHECK VALVE AND
TO DRAIN DOWNSPOUT
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10.1 RTI Manifold and Accessories cont.
ITEM
PART #
106-6830
108-0446
810-1668
220-5658
807-4760
810-1057
810-1668
810-1069
813-0555
810-3531
810-3583
810-3596
813-0003
810-3738
813-0062
813-0093
813-0062
813-0261
813-0304
813-0345
813-0336
813-0838
220-5656
220-5657
823-7142
810-3587
809-0601
COMPONENT
√
1
2
3
4
5
6
7
8
Solenoid Assembly
Valve, RTI Waste Assembly (see page 2-32 for parts)
Adaptor, Male ⅝” OD x ½”
Cover, RTI Dust Plug
Harness, RTI – MIB connection
Flexline, ⅝” OD x 13-inch long
Adaptor, Male ⅝” OD x ½”
Flexline, ⅝” OD x 29.50-inch long
Reducer, Bell Fitting, ½” to ¼” NPT BM
Valve, Check 20 PSI RTI bypass
Valve, Check ½” NPT 4 PSI RTI Manifold
Manifold, RTI
Tee, ½” x ½” x ½” BM
Adaptor, Check Valve Close Nipple
Elbow, ½” Blk 90°
Nipple, ½” x 4-inch
Elbow, ½” BM 90°
Nipple, ½” x 5-inch NPT
Bushing, ½” x ¼”
Elbow, ½ Blk 45°
Plug, ½” NPT Square Head
Nipple, ¼” NPT
Brace, RTI Handle
Cover, RTI Handle
Handle, RTI Waste Pull
Lock and Key, RTI Waste Handle
Clip, Clevis Left Rod End
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
√ Recommended parts.
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10.2 RTI Dispose Waste Valve
ITEM
PART #
108-0446
108-0445
220-5615
807-4936
810-0278
900-2935
901-2348
902-2348
COMPONENT
Valve, RTI Dispose Waste
Bracket, RTI Waste Valve
Handle, RTI Waste Valve
Microswitch, Gold Sealed
Valve, ½” Ball
1
2
3
4
5
6
7
Retainer, Nut Return Valve
Cover, DV Safety Switch
Cover, DV Safety Switch
2.10.3 RTI Test Box
ITEM
PART #
COMPONENT
√
108-0716
Box, LOV™ RTI Test
√ Recommended parts.
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11 Wiring Connectors, Pin Terminals and Power Cords
ITEM
PART #
COMPONENT
Power Cords
*
*
*
*
*
807-0154
807-4317
807-1685
807-4316
807-3817
807-5105
100/120V–15A 3-wire, w/grounded plug
100/208/240V-16A 3-Wire with Plug LOV CE
100/208/240V–18A 3-wire, w/o plug
120V 5-wire, w/grounded plug LOV
208/240V 3-Phase 4-wire w/grounded plug
208/240V 3-Phase 4-wire w/grounded plug 105” CE 4 battery or
larger
*
Connectors and Tools
1
2
3
5
5
6
7
8
9
10
11
12
13
14
15
16
*
807-1068
807-0158
807-0156
807-0159
807-0875
807-1067
807-0157
807-0155
807-0160
807-0804
826-1341
826-1342
807-2518
807-0928
806-4855
230-2345
807-4660PK
2-Pin Female
6-Pin Female
9-Pin Female
12-Pin Female
15-Pin Female
2-Pin Male
6-Pin Male
9-Pin Male
12-Pin Male
15-Pin Male
Terminal, Female Split Pin (Pkg of 25)
Terminal, Male Split Pin (Pkg of 25)
Plug, Mate-N-Lock (Dummy Pin)
Extract Tool Pin Pusher
Pin Pusher Screwdriver Assembly
SMT Pin Extractor
SMT Pin Service Repair Kit
* Not illustrated.
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
2.12 Fasteners
PART #
ITEM
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
COMPONENT
Bolt, ¼-inch – 20 x 2.00-inch Hex Head ZP Tap
Bolt, ¼-inch -20 x ¾-inch Hex
Cap Screw, 5/16-inch-18 5.50” NC Hex (Connects pump to motor.)
Clip, Tinnerman
Nut, 4-40 Keps Hex (Pkg. of 25) (809-0237)
Nut, 6-32 Keps Hex (Pkg. of 25) (809-0049)
Nut, 8-32 Keps Hex
Nut, 10-32 Keps Hex (Pkg. of 10) (809-0256)
Nut, 10-32 Keps Hex SS
Nut, ½ NPT Locking
Nut Cap 10-24 NP
Nut Grip ¼-inch ¼-20 Hex NP (Pkg. of 10) (809-0059)
Nut Flange ¼-inch ¼-20 Serr
Nut, "T" ¼-inch-20 x 7/16 SS
809-0429
809-0131
809-1020
809-0448
826-1366
826-1358
809-0247
826-1376
809-0766
809-0581
809-0020
826-1372
809-0417
809-0535
809-0495
809-0540
826-1359
826-1365
809-0357
809-0359
809-0360
826-1371
809-0364
809-0518
809-0104
826-1363
826-1360
826-1330
809-1003
809-0270
826-1375
809-1000
826-1374
809-0266
809-0434
809-0123
826-1389
809-0582
809-0184
809-0190
809-0191
809-0193
809-0194
Nut, ¼-inch – 20 Press
Nut, Lock ½-inch-13 Hex 2-Way ZP
Screw, 4-40 x ¾-inch Slotted Round Head (Pkg. of 25) (809-0354)
Screw, 6-32 x ⅜-inch Slot Head (Pkg. of 25) (809-0095)
Screw, 6 x ⅜-inch Phillips Head NP
Screw, 8 x ¼-inch Hex Washer Head
Screw, 8 x ⅜-inch Hex Washer Slot Head
Screw, 8 x ½-inch Hex Head ZP (Pkg. of 25) (809-0361)
Screw, 8 x ⅝-inch Hex Washer Head ZP
Screw, 8-32 x ⅜-inch Hex Washer Slotted Head SS
Screw, 8-32 x ½-inch Slotted Head ZP
Screw, 8-32 x ½-inch NP (Pkg. of 25) (809-0103)
Screw, 10-24 x 5/16-inch Round Slot Head ZP (Pkg. of 25) (809-0024)
Screw, 10-32 x ⅜-inch Slot Head SS (Pkg. of 25) (809-0117)
Screw, 10-32 x ⅜-inch Hex Trim Head SS
Screw, 10-32 x ½-inch Phillips Head ZP
Screw, 10-32 x ¾-inch Hex Trim Head SS (Pkg. of 5) (809-0401)
Screw, 10-32 x 1¼-inch Hex Sck C/S
Screw, 10 x ½-inch Hex Head (Pkg. of 25) (809-0412)
Screw, 10 x ½-inch Phillips Head ZP
Screw, 10 x ⅜-inch Hex Washer Head NP
Screw, 10 x ¾-inch Slot Head
Screw, 1/4-20 x ¾-inch Hex Head ZP (Pkg. of 10) (809-0131)
Washer ½ NPT Locking
Washer, #10 LK ZP
Washer, .625 X .275 X 40 Flat SS
Washer, Lock ¼ Spring ZP
Washer, Flat ¼ Nylon
Washer, Flat 5/16 ZP
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONALLY LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
Frymaster, L.L.C., 8700 Line Avenue, Shreveport, Louisiana 71106
TEL 1-318-865-1711
FAX (Parts) 1-318-219-7140
(Tech Support) 1-318-219-7135
819-6446
MAY 2011
SERVICE HOTLINE
1-800-551-8633
PRINTED IN THE UNITED STATES
Download from Www.Somanuals.com. All Manuals Search And Download.
|